INFODRAW PMRS-420 Скачать руководство пользователя

Страница: 172 / 191

15 June, 2017

INFODRAW R&D

PMRS-420 (v2.0) User Manual v6.2.0.0

168

4-4-8 Sleep Management

If you want your device to save power and to open remotely when you tell it to or in a pre-set date,
please enact the following instructions in order to impose a sleep regiment on your PMRS device.



This service only applies to software and firmware version 4.5.0.0 and later.

Activate your device and connect it to your server -in this example we connected the PMRS
device to the IP address: "mrs1.infodraw.com"

6. Close the device manually. It will go into sleep mode.

After connecting the device, open

the MRS Service program by
opening your browser and entering:
SERVER_IP_ADDRESS:12654/admin

3. To configure the sleep
management, under the Sleep
management section - click on the
configure option.

4. Click on "Add Device" to install a
sleep regiment for your device.

5. Enter how often you want your device to wake up to look
for a signal or set a date for its awakening - apply the
changes.

Содержание PMRS-420
































































































































































































Результаты поиска

Содержание PMRS-420

Отзывы:

Похожие инструкции для PMRS-420

Бренды по названию

Популярные бренды

INFODRAW PMRS-420, Руководство пользователя

Результаты поиска

Содержание PMRS-420

Отзывы:

Похожие инструкции для PMRS-420

Бренды по названию

Популярные бренды