Infinova V1700 Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 27

Infinova V1700 Series Скачать руководство пользователя страница 17

please refer to the following figure (Unit: mm).

A

A view

2 thick

130

10

0

80

R3

135

°

160

120

60

8 7

Figure 3-21. Installing Bracket Base

2.

Use the four screws supplied with the mount bracket to secure
the bracket onto the base. Pull the wiring through the mount
bracket.

Figure 3-22. Installing Mount Bracket

3.

Take out the upper housing from the dome package. Loosen the
bolt that holds the connection circuit board, and lift the board for
wiring connection.

Figure 3-23. Lifting Connection Board

4.

Pull the cables through the opening, and then screw the upper
housing onto the mount bracket. For outdoor housing, it is
recommended to apply thread compound to the threads on the
housing. Secure the connection with a holding screw.

Holding Screw

Outdoor Mounting

Holding Screw

Indoor Mounting

Figure 3-24. Installing Housing

5.

Connect system cables (power, communication and video) to the
connection circuit board inside the housing. For outdoor dome,
make sure that the heater and fan are also properly connected.
Then, push the board back to its original position, and tighten the
holding screw to close the opening.

6.

Take out the dome drive from the dome package. Set the camera
ID by configuring the DIP switch S1. Set the communication
baud rate and protocol by configuring the DIP switch S2. For
detail on how to configure the DIP switch, please refer to

Appendix I

and

II.

Figure 3-25. DIP Switch S1, S2

7.

Line up the two tabs located on the upper side of the dome drive
with the corresponding grooves in the housing. Insert both tabs
into the grooves. Push up the dome insert until both tabs click
into place. Be sure that you hear two clicks.

Tab

Tab

Indoor mounting Outdoor mounting

Figure 3-26. Installing Dome Drive

8.

Take out the dome bubble from the dome package and fix the
safety cord. As one end of safety cord has already fixed to the
upper housing, and the other end should be tied to the dome
bubble. (For outdoor domes, at the same time, connect cable
terminal of temperature control switch in the housing with that of
heater in the dome bubble. Position the junction in the spacing
between heater gasket and outer space of the dome bubble). At
last, locate dome bubble onto upper housing in correct direction
and line up the screw holes of the dome bubble with
corresponding holes on the housing, and then secure the cover

11

«
...
15
16
17
18
19
...
»

Содержание V1700 Series




























Отзывы:

Нет отзывов