Infinova V1691 Series Скачать руководство пользователя страница 3

 

Notice

 

 

Copyright Statement 

This manual may not be reproduced in any form or by any means to create any derivative such as translation, transformation, or adaptation 

without the prior written permission of Infinova. 

 
Infinova reserves the right to change this manual and the specifications without prior notice. The most recent product specifications and 

user documentation for all Infinova products are available on our website www.infinova.com. 

 

Trademarks 

Infinova

®

 

is a trademark of Infinova.

 

 
Copyright © 2000-2009 Infinova. All rights reserved. 
 
All other trademarks that may appear belong to their respective proprietors. 

 

FCC Warning 

V1691 Series Receiver/drivers all comply with Part 15 of the FCC rules. 
 
Operation is subject to the following two conditions. 

z

 

This device may not cause harmful interference. 

z

 

This device must accept any interference received, including interference that may cause undesired operation. 

 
V1691 Series Receiver/drivers have been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the 

FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a 
residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference 
will not occur in a particular installation. 

Содержание V1691 Series























Отзывы: