Step 5:
Carefully lift arm panel and
hook the arm panel clip on to
the chair body rail (connection
location B from step 3). Make
sure the air hoses and
electrical wires remain
connected and not pinched.
Slide the arm panel back
towards the chair body as far
as it will go.
5
Step 6:
Next locate the arm panel
pin in position A
(see step
3 insert)
and secure it
into the chair body pin
retainer in position A.
Ensure the arm panel clip
remains on the chair
body rail as you lift up the
front of the arm panel
slightly. Make sure both
connections at point A
and B are firmly in place
before continuing.
6
Step 7:
To secure the arm panel to the chair body, locate the screw hole on the
inside of the arm panel by the foot well and insert an M6x20mm Bolt and
M6x14mm Washer. Hand Tighten. Next, locate the screw hole where the
top of the arm panel overlaps the bottom of the shoulder panel. Insert an
M8x30mm bolt and M8x14mm washer into the arm panel connector, and
then insert into the screw hole. Tighten both bolts with provided hex key.
Repeat steps 6-8 on other side of chair.
7
Step 8:
Before attaching, ensure the airbag on the inward facing side of the
shoulder panel is toward the front of the chair. Locate the shoulder panel
mounting brackets on the outward facing side of the shoulder panel. Slide
the mounting brackets into the chair body mounting channels. Before sliding
the shoulder panel all the way on, connect the electrical cord to the
electrical plug until it clips, then connect the air hose firmly onto the air hose
nozzle. Carefully guide the air hose inside the chair body as you slide the
assembly into place firmly down and against the chair body.
8
Step 9:
Once the shoulder panel is in
place on the chair body
mounting bars, un-zip the
zipper found underneath the
shoulder airbag for easy
access to screw holes. Look
under the airbags to expose
the screw holes on each side
and insert four M5x20mm
screws into the screw holes.
Tighten with screwdriver.
Close the shoulder airbag
zipper once complete.
Step 10:
To secure the shoulder
panel to the chair body,
insert one M5x20mm
screw into the top screw
hole, and two M4x16mm
screws into the bottom
screw holes. Tighten with
screwdriver.
10
9
Step 11:
Connect the chair power
cord to a grounded 110V
electrical outlet and plug it
into the respective port on
the back side of the base
of the chair. Flip the main
power switch to on. Press
the power button on the
quick access control panel,
located on the left arm
panel to bring the chair
into an upright position.
Once chair is in upright
position, and before
continuing, turn the main
power switch off.
11
Step 12:
Locate the tablet holder from the
accessory box. Use the screw
driver to remove the two M4x12mm
screws from the tablet holder
mount, making sure the mount
stays attached to the chair once
screws are removed. Place the
tablet holder into the tablet holder
mount and then re-insert the two
M4x12mm screws into the screw
holes to secure the holder in place.
Next, attach the tablet mount cover
to the tablet holder mount and push
into place to secure. Place the
tablet remote into the tablet holder.
Connect the tablet remote cord to
the tablet remote port, making sure
the notches on either end line up.
12
Step 14:
Remove the footrest from
its packaging and position it
in front of the main chair
body. Connect the footrest
electrical plug into the
footrest electrical port.
Ensure the thumb release is
facing up and push in until it
clips. Next, slide the air hose
firmly onto the air nozzle.
13
14
Step 13:
Before attaching the footrest to the chair body, remove the clips on the
chair body footrest pins by sliding up. (If Clips are missing, there are spare
clips in the Accessory Box). Next, attach the footrest sleeves to the
footrest mounting bracket as shown.
Arm Panel
Clip
Chair Body Rail
Chair Body
Pin Retainer
Arm Panel Pin
Step 3 Insert
A
Chair Body
Pin Retainer
Arm Panel Pin
Zipper
Shoulder Airbag
Screw holes
4x
(M5x20mm Screw)
Top
Screw hole
Bottom
Screw holes
2x
(M4x16mm Screw)
1x
(M5x20mm Screw)
Clip
Chair Body
Footrest Pin
Chair Body
Footrest Pins
Footrest
Mounting Bracket
M6x20mm Bolt
M6x14mm Washer
M8x30mm Bolt
M8x14mm Washer
Arm Panel Connector
Shoulder
Airbag
Air Hose
Nozzle
Air Hose
Electrical Plug
Electrical Cord
Chair Body
Mounting Channels
*outward facing*
Shoulder Panel
*inward facing*
Shoulder
Panel Mounting
Brackets
Screw
Hole
Screw
Hole
Footrest
Main power switch
Power cord
port
Air nozzle
Air hose
Footrest
electrical plug
Footrest
electrical port
Leads
from the
Footrest
Footrest
Sleeve
Tablet
Holder
Tablet
Remote Port
Tablet
Remote Cord
Line up
Notches
Tablet Mount
Cover
Tablet Holder
Mount
Tablet
Remote
