6
PRIMUS PS-8
Power On
Plug your subwoofer’s AC cord into a wall outlet. Do not use the
outlets on the back of the receiver.
Initially set the Subwoofer Level Control
¡
to the “min” position.
Turn on your sub by pressing the Power Switch
•
on the rear panel.
Turn on your entire audio system and start a CD or movie sound-
track at a moderate level.
Auto On/Standby
With the Power Switch
•
in the ON position, the subwoofer
will automatically enter the Standby mode after approximately
10 minutes when no signal is detected from your system. The
subwoofer will then power ON instantly when a signal is detected.
During periods of normal use, the Power Switch
•
can be left
on. You may turn off the Power Switch
•
for extended periods of
nonoperation; e.g., when you are away on vacation.
Adjust Level
Turn your Subwoofer Level Control
¡
up to the “5” position (half
way). If no sound emanates from the subwoofer, check the AC-line
cord and input cables. Are the connectors on the cables making
proper contact? Is the AC plug connected to a “live” receptacle?
Has the Power Switch
•
been turned to the “On” position? Once
you have confirmed that the subwoofer is active, proceed by
playing a CD, record or cassette. Use a selection that has ample
bass information.
Set the overall volume control of the preamplifier or stereo to a
comfortable level. Adjust the Subwoofer Level Control
¡
until
you obtain a pleasing blend of bass. Bass response should not
overpower the room but rather be adjusted so there is a
harmonious blend across the entire musical range. Many users
have a tendency to set the subwoofer volume too loud, adhering
to the belief that a subwoofer is there to produce lots of bass.
This is not entirely true. A subwoofer is there to enhance bass,
extending the response of the entire system so the bass can
be felt as well as heard. However, overall balance must be
maintained or the music will not sound natural. An experienced
listener will set the volume of the subwoofer so its impact on
bass response is always there but never obtrusive.
Phase Control
The Phase Switch
£
determines whether the subwoofer
speaker’s piston-like action moves in and out with the main
speakers, 0˚, or opposite the main speakers, 180˚. Proper phase
adjustment depends on several variables such as room size,
subwoofer placement and listener position. Adjust the phase
switch to maximize bass output at the listening position.
O
PERATION
Crossover Adjustment
The Crossover Adjustment control
™
determines the highest
frequency at which the subwoofer reproduces sounds. If your main
speakers can comfortably reproduce some low-frequency sounds,
set this control to a lower frequency setting, between 50Hz
and 100Hz. This will concentrate the subwoofer’s efforts on the
ultradeep bass sounds required by today’s films and music. If you
are using smaller bookshelf speakers that do not extend to the
lower bass frequencies, set the Low-Pass Frequency Adjustment
control to a higher setting, between 120Hz and 150Hz.
NOTE: This control will have no effect if the LFE Input
¢
is set
to “LFE.”If you have a Dolby Digital or DTS processor/receiver, the
Low-Pass Frequency is set by the processor/receiver. Consult your
owner’s manual to learn how to view or change this setting.
M
AINTENANCE AND
S
ERVICE
The enclosure may be cleaned using a soft cloth to remove
fingerprints or to wipe off dust.
The grille may be gently vacuumed. Stains may be removed with
an aerosol cleaner, following its instructions. Do not use any
solvents on the grille.
All wiring connections should be inspected and cleaned or
remade periodically.The frequency of maintenance depends on
the metals involved in the connections, atmospheric conditions,
and other factors, but once per year is the minimum.
In the event that your Primus subwoofer ever needs service,
contact your local Infinity dealer or distributor.
Primus PS-8 OM 10/17/03 9:31 AM Page 6