background image

!

 

 

USER MANUAL    |   

 

!

"$!

 
 
FEDERAL COMMUNICATIONS COMMISSION 
 

Federal Communications Commission (FCC) Statement

 

15.21

 

You  are  cautioned  that  changes  or  modifications  not  expressly  approved  by 
the part responsible for compliance could void the user’s authority to operate 
the equipment.

 

15.105(b)

 

This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a 
Class  B  digital  device,  pursuant  to  part  15  of  the  FCC  rules.  These  limits  are 
designed  to  provide  reasonable  protection  against  harmful  interference  in  a 
residential  installation.  This  equipment  generates,  uses  and  can  radiate  radio 
frequency  energy  and,  if  not  installed  and  used  in  accordance  with  the 
instructions,  may  cause  harmful  interference  to  radio  communications. 
However, there is no guarantee that interference will not occur in a particular 
installation.  If  this  equipment  does  cause  harmful  interference  to  radio  or 
television  reception,  which  can  be  determined  by  turning  the  equipment  off 
and  on,  the  user  is  encouraged  to  try  to  correct  the  interference  by  one  or 
more of the following measures: 

- Reorient or relocate the receiving antenna.

 

- Increase the separation between the equipment and receiver.

 

-  Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to 
which the receiver is connected.

 

- Consult the dealer or an experienced radio/TV technician for help.

 

Operation is subject to the following two conditions: 

1) this device may not cause interference and

 

2)  this  device  must  accept  any  interference,  including  interference  that  may 
cause undesired operation of the device.

 

FCC RF Radiation Exposure Statement:

 

This  equipment  complies  with  FCC  radiation  exposure  limits  set  forth  for  an 
uncontrolled  environment.  End  users  must  follow  the  specific  operating 

Содержание INFINEA TAB Series




























Отзывы: