Infineon XC886CLM Скачать руководство пользователя страница 353 | Manualshive

Страница: 353 / 663

background image

XC886/888CLM

Capture/Compare Unit 6

User’s Manual

14-1

V1.3, 2010-02

CCU6, V 1.0

14

Capture/Compare Unit 6

The Capture/Compare Unit 6 (CCU6) provides two independent timers (T12, T13), which
can be used for Pulse Width Modulation (PWM) generation, especially for AC-motor
control. The CCU6 also supports special control modes for block commutation and
multi-phase machines. The block diagram of the CCU6 module is shown in

Figure 14-1

The timer T12 can function in capture and/or compare mode for its three channels. The
timer T13 can work in compare mode only.

The multi-channel control unit generates output patterns, which can be modulated by
T12 and/or T13. The modulation sources can be selected and combined for the signal
modulation.

Timer T12 Features:

•

Three capture/compare channels, each channel can be used either as a capture or
as a compare channel

•

Supports generation of a three-phase PWM (six outputs, individual signals for
highside and lowside switches)

•

16-bit resolution, maximum count frequency = peripheral clock frequency

•

Dead-time control for each channel to avoid short-circuits in the power stage

•

Concurrent update of the required T12/13 registers

•

Generation of center-aligned and edge-aligned PWM

•

Supports single-shot mode

•

Supports many interrupt request sources

•

Hysteresis-like control mode

Timer T13 Features:

•

One independent compare channel with one output

•

16-bit resolution, maximum count frequency = peripheral clock frequency

•

Can be synchronized to T12

•

Interrupt generation at period-match and compare-match

•

Supports single-shot mode

Additional Features:

•

Implements block commutation for Brushless DC-drives

•

Position detection via Hall-sensor pattern

•

Automatic rotational speed measurement for block commutation

•

Integrated error handling

•

Fast emergency stop without CPU load via external signal (CTRAP)

•

Control modes for multi-channel AC-drives

•

Output levels can be selected and adapted to the power stage

*

«
...
351
352
353
354
355
...
»

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

Бренд: IBM Страницы: 144

Бренд: Rain Bird Страницы: 24

ESP-LXIVM Series

Бренд: Rain Bird Страницы: 16

Бренд: YASKAWA Страницы: 360

Бренд: NCE Страницы: 4

Бренд: V2 Страницы: 108

Бренд: R-Tec Страницы: 14

Бренд: Vectornav Страницы: 18

Бренд: DIG Страницы: 16

Бренд: Danfoss Страницы: 6

Бренд: Pellet Grill Outlet Страницы: 4

Бренд: PacComm Страницы: 29

Бренд: Knoll Страницы: 3

Бренд: ZKTeco Страницы: 15

Бренд: Fireye Страницы: 24

Бренд: Schalk Страницы: 12

Бренд: Cytron Technologies Страницы: 20

Бренд: Atmel Страницы: 1163

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды