Infineon XC886CLM Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 663

background image

XC886/888CLM

Introduction

User’s Manual

1-2

V1.3, 2010-02

Introduction, V 1.1

shows the functional units of the XC886/888.

Figure 1-1

XC886/888 Functional Units

The XC886/888 product family features devices with different configurations, program
memory sizes, package options, temperature and quality profiles (Automotive or
Industrial), to offer cost-effective solutions for different application requirements.

The list of XC886/888 device configurations are summarized in

. For each

configuration, 2 types of packages are available:

•

TQFP-48, which is denoted by XC886 and;

•

TQFP-64, which is denoted by XC888.

Table 1-1

Device Configuration

Device Name

CAN
Module

LIN BSL
Support

MDU
Module

XC886/888

No

No

No

XC886/888C

Yes

No

No

XC886/888CM

Yes

No

Yes

XC886/888LM

No

Yes

Yes

XC886/888CLM

Yes

Yes

Yes

Port 0

Port 1

Port 2

Port 3

XC800 Core

UART

ADC

10-bit

8-channel

Boot ROM

12K x 8

XRAM

1.5K x 8

RAM

256 x 8

On-Chip Debug Support

Timer 0

16-bit

Timer 1

16-bit

Timer 2

16-bit

UART1

SSC

Flash or ROM

1)

24K/32K x 8

Capture/Compare Unit

16-bit

Compare Unit

16-bit

8-bit Digital I/O

8-bit Digital I/O

8-bit Digital I/O

8-bit Digital/
Analog Input

1) All ROM devices come with an additional 4K x 8 Flash

Port 4

Port 5

MDU

CORDIC

MultiCAN

Timer 21

16-bit

Watchdog

Timer

8-bit Digital I/O

8-bit Digital I/O

Improved functionality in comparison to the XC866

*

«
...
14
15
16
17
18
...
»

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

Бренд: Data Aire Страницы: 13

Бренд: Garmin Страницы: 4

Бренд: Lawler Страницы: 5

Бренд: National Instruments Страницы: 6

Бренд: National Instruments Страницы: 40

Бренд: National Instruments Страницы: 28

Бренд: National Instruments Страницы: 7

Бренд: I-Tork Страницы: 15

Optidrive Elevator

Бренд: Invertek Страницы: 5

Бренд: Techtrol Страницы: 4

Synergy SGY-101

Бренд: Fairford Страницы: 20

Бренд: ST Страницы: 40

Бренд: Varian Страницы: 37

Бренд: Melexis Страницы: 13

Бренд: Pellet Grill Outlet Страницы: 4

Бренд: XINGDASHINE Страницы: 3

Giatsu GIA-J105

Бренд: GIA Страницы: 9

Бренд: Arbor Technology Страницы: 79

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды