manualshive.com logo in svg

Infineon Technologies TC1796, Руководство пользователя

Продукт Infineon Technologies TC1796 - это мощный микроконтроллер для различных приложений в автомобильной промышленности. Пользовательский мануал доступен для скачивания бесплатно с нашего веб-сайта. Главное - ознакомиться с этим руководством перед началом использования устройства. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

TC1796

System Units (Vol. 1 of 2)

LMB External Bus Unit

 

User’s Manual

13-57

V2.0, 2007-07

EBU, V2.0

 

13.8.6

Dynamic Command Delay and Wait State Insertion

In general, there are two critical phases during asynchronous device accesses. These
phases are:
•

Command Delay Phase

 (see 

Page 13-43

).

•

Command Phase

 (see 

Page 13-43

).

In the EBU, internal length programming for these two phases is available via bit field
EBU_BUSAPx.CMDDELAY. This bit field determines the basic number of Command
Delay phase clock cycles. The total number of Command Delay phase clock cycles
further depends on the settings of bit field EBU_BUSCONx.CMULT and
EBU_BUSCONx.MULTMAP[2].
The equivalent control capability is available for bit fields EBU_EMUBAP.CMDDELAY,
EBU_EMUBCx.CMULT, and EBU_EMUBCx.MULTMAP[2]. The WAIT functionality as
described in the next two subsections, has also an equivalent control capability for the
bit fields EBU_EMUBC.CMDDELAY, EBU_EMUAP.WAITRDC, and
EBU_EMUAP.WAITWRC.

13.8.6.1 External Extension of the Command Phase by WAIT

The WAIT input can be used to cause the EBU to extend the Command Phase by
inserting additional cycles prior to deactivation of the RD and RD/WR lines. This signal
can be programmed separately for each region to be ignored or sampled either
synchronously or asynchronously (selected via the EBU_BUSCONx.WAIT or
EBU_EMUBC.WAIT bit field). Additionally, the polarity of WAIT can be programmed for
active low (default after reset) or active high function via bit EBU_BUSCONx.WAITINV
or EBU_EMUBC.WAITINV. The signal will only take effect after the programmed number
of Command Phase cycles has passed. This means that the signal can only be used to
extend the phase, not to shorten it.
When programmed for synchronous operation, WAIT is sampled on every rising edge of
LMBCLK during the Command Phase. The sampled value is then used on the next rising
edge of LMBCLK to decide whether to prolong the Command Phase or to start the next
phase. 

Figure 13-20

 shows an example of WAIT used in Synchronous Mode.

Note: Due to the one-cycle delay in Synchronous Mode between the sampling of the

WAIT input and its evaluation by the EBU, the Command Phase must always be
programmed to be at least one LMBCLK cycle (via EBU_BUSAPx.WAITRDC or
EBU_BUSAPx.WAITWRC) in this mode.

When programmed for asynchronous operation, WAIT is also sampled at each rising
edge of LMBCLK during the Command Phase. However, an extra synchronization cycle
is inserted prior to the use of the sampled value. This means that the sampled value is
not used until the second following rising edge of LMBCLK. 

Figure 13-21

 shows an

example of WAIT used in Asynchronous Mode.

Содержание TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TC1796

XBOX 360 Quick Manual preview
360
Бренд: XBOX Страницы: 2
FrSky Taranis Q X7S Manual preview
Taranis Q X7S
Бренд: FrSky Страницы: 2
ZIMO MX10 Instruction Manual preview
MX10
Бренд: ZIMO Страницы: 38
VAT 620 Series Installation, Operating, & Maintenance Instructions preview
620 Series
Бренд: VAT Страницы: 26
MAKOT UMS-02 Manual preview
UMS-02
Бренд: MAKOT Страницы: 6
Neets echo plus User Manual preview
echo plus
Бренд: Neets Страницы: 12
National Instruments NI 9871 Operating Instructions And Specifications preview
NI 9871
Бренд: National Instruments Страницы: 24
ValvTechnologies V1 Series Installation And Operations Maintenance Manual preview
V1 Series
Бренд: ValvTechnologies Страницы: 20
YASKAWA PROFINET V1000 Technical Manual preview
PROFINET V1000
Бренд: YASKAWA Страницы: 49
M-system MSP10 Instruction Manual preview
MSP10
Бренд: M-system Страницы: 17
ZIMMERLI MESSTECHNIK LPS Series Operating Manual preview
LPS Series
Бренд: ZIMMERLI MESSTECHNIK Страницы: 12
H-Tronic TS 125 Manual preview
TS 125
Бренд: H-Tronic Страницы: 32
Allen-Bradley PowerFlex 755 IP00 Installation Instructions Manual preview
PowerFlex 755 IP00
Бренд: Allen-Bradley Страницы: 78
GI.BI.DI AS05582 Installation Instructions Manual preview
AS05582
Бренд: GI.BI.DI Страницы: 60
Tormatic DuoControl Signal 111 Quick Start Manual preview
DuoControl Signal 111
Бренд: Tormatic Страницы: 3
Zencontrol zc-iot-fc Quick Start Manual preview
zc-iot-fc
Бренд: Zencontrol Страницы: 2
Gasboy CFN Series Startup Manual preview
CFN Series
Бренд: Gasboy Страницы: 119
FMS 109753-KIM Manual preview
109753-KIM
Бренд: FMS Страницы: 108

Бренды по названию

Популярные бренды

Загрузить еще бренды