Inficon UL5000 Скачать руководство пользователя страница 91

Страница: 91 / 108

Maintenance works

iina

e 0

chn

ica

l ha

boo

9.5

Maintenance groups

The maintenance plan for the UL5000 can be subdivided in 4 maintenance groups.

•

1500 hours maintenance

•

4000 hours maintenance

•

8000 hours maintenance

•

16000 hours maintenance

9.5.1

1500 hours maintenance

The 1500 hours maintenance can be performed by an operator or a maintenance
person.

The filter cell in front of the fans should be checked and replaced if dirty. By operating
under worth conditions, the maintenance rates can be appropriatly reduced.

Replace the silencer at the exhaust of the leak detector.

Notice:

An obstructed silencer can lead to damaging the scroll pump

Work to be performed

Required materials

P/N

Check and/or replace filters

Replace silencer

•

Spare filter cell for the fans

•

Silencer for the exhaust

200000685

20099183

Содержание UL5000













































































































Результаты поиска

Содержание UL5000

Отзывы:

Похожие инструкции для UL5000

Бренды по названию

Популярные бренды

Inficon UL5000, Техническое руководство

Результаты поиска

Содержание UL5000

Отзывы:

Похожие инструкции для UL5000

Бренды по названию

Популярные бренды