Inficon IMM-200 Скачать руководство пользователя страница 21

Страница: 21 / 67

INFICON

Installation and Interfaces | 5

074-733-P1A IMM-200 Operating Manual

21 / 67

5 Installation and Interfaces

Before permanently installing IMM-200, read this entire chapter. Follow the

recommendations as closely as possible. INFICON has taken numerous steps to

ensure its equipment will operate in a variety of harsh situations. Failure to adhere to

these simple practices may adversely affect the performance and longevity of

IMM-200.

NOTICE

Use caution when mounting IMM-200 to a fixed position. Ensure there is

enough room to disconnect the power cord when needed.

5.1 Avoiding Electrical Interference

Careful consideration of simple electrical guidelines during installation avoids many

problems caused by electrical noise. To maintain the required shielding and internal

grounding and ensure safe and proper operation, IMM-200 must be operated with all

enclosure covers, sub-panels, and braces in place and fully secured with the screws

and fasteners provided.

Verifying / Establishing

Earth Ground

If ground must be established, the following procedure is recommended:

► Where soil conditions allow, drive two ten-foot copper clad steel rods into the

ground six feet apart. Pour a copper sulfate or a salt solution around each rod to

improve the ground’s conduction. A near-zero resistance measurement indicates

earth ground is achieved.

Keep the connections to this grounding network as short as possible.

Connections to Earth

Ground

There are two required earth ground connections:

1. The earth ground connection on IMM-200 is a threaded stud with a hex nut.

Connect a ring terminal to the ground strap, allowing a good connection and easy

removal and installation. This connection must be made at installation. For best

protection against high frequency noise, the length-to-width ratio of the earth

conductor should not exceed a ratio of 5:1. The ground strap should connect from

IMM-200 to the vacuum system as shown.

Содержание IMM-200




































































Результаты поиска

Содержание IMM-200

Отзывы:

Похожие инструкции для IMM-200

Бренды по названию

Популярные бренды

Inficon IMM-200, Руководство по эксплуатации

Результаты поиска

Содержание IMM-200

Отзывы:

Похожие инструкции для IMM-200

Бренды по названию

Популярные бренды