.
Other:
Jaskr.
display brightness 00 to 16
Język
menu language English (EN), French (FR), German (DE), Polish (PL)
2.
Registering the remote controls
PIL-19/99PMT remote control can be used to control any channel, provided that the channel has been previously registered for a specific motor or controller.
Entering the programming mode:
Initial programming of radio controlled drives and ST-01RL controllers:
-
connect 230 VAC power supply to the drive/controller,
-
press ▲ “UP” and ▼ “DOWN” simultaneously within 10 seconds from the power-on
(
is momentarily displayed),
-
the drive will move up and down,
-
press ▲ “UP” on the selected remote control channel within 10 seconds,
-
short up and down movement of the drive confirms the registration.
NOTE: This will remove all the previously registered remote controls from the drive memory.
Programming ST-01R controller:
-
press S1 - LED will blink and light,
-
press ▲ “UP” on the remote control,
-
LED will blink green and red to confirm registration of the remote control,
For a previously registered remote control
Other remote controls can be registered without switching off the power. Enter the drive/controller programming mode using a previously
registered remote control.
-
press ▲ “UP” and ▼ “DOWN” simultaneously after selecting a previously registered channel,
-
the drive will move up and down in a series of short movements corresponding to the number of registered remote controls,
-
press ▲ “UP” for a new channel or on a new remote control within 10 seconds,
-
the drive will move up and down in a series of short movements to confirm registration of the next channel.
3.
Activating the roller shutter:
Press ▲ “UP” (open) or ▼ “DOWN” (close) to activate the drive. Press “STOP” to interrupt. After 15 seconds without any activity (no button pressed),
the remote control switches to standby mode (reduced power consumption). By default, the remote control is in standby mode. Press any key to activate
(LED corresponding to the last selected number will light, no action is taken), press again to execute the selected command.
4.
Activating the roller shutter:
Press
to enter the roller shutter mode (slat adjustment). The drive moves slightly. Three horizontal lines are displayed above the
channel number.
Press ▲ “UP” or ▼ “DOWN” to adjust the slats. Press
to return to normal mode.
CAUTION!
The roller shutter must be stopped before adjusting the slats. Press STOP before adjusting the slats, if the slats cannot
be adjusted via the remote control.
5.
Selecting channel in PIL-19PMT (PIL-99PMT easy mode):
Press ◄ “LEFT” to select previous channel.
Press ► “RIGHT” to select next channel.
6.
Selecting channel in PIL-99PMT:
A single channel (01 to 99) can be selected (PIL-99PMT). Procedure:
Press ◄ “LEFT” to change the left digit (tens); up/down arrow is displayed. Press ▲ “UP” or ▼ “DOWN” to change the
selected value and press ◄ “LEFT” again to exit.
Press ► “RIGHT” to change the right digit (units); up/down arrow is displayed. Press ▲ “UP” or ▼ “DOWN” to change
the selected value and press ► “RIGHT” again to exit.
If the value is not changed, pressing ▲, ▼ or STOP will send a command (open, close) to an individual controller or a group
of controllers.
To enable (or disable) easy (sequential) mode in PIL-99PMT: select the highest channel number used and press ◄ “LEFT” and
► “RIGHT” simultaneously. “S” followed by a number of the highest channel number used is displayed.
In easy mode, the
number of selectable channels
(► and ◄)
is limited
.
You can select channels from 0 to the highest channel number used.
7.
Replacing the batteries:
The remote control uses two 3V CR 2032 batteries.
Remove the battery cover at the bottom of the remote control. Replace the battery (“+” sign facing up).
It is not permitted to dispose of waste equipment together with other waste. Dispose only in specially designated areas. The household plays a key
role in the recycling of waste equipment. By correct sorting of waste, including waste equipment and batteries, household members ensure that the
equipment is not disposed together with household waste, but in specially designated areas, and thus may be used again after recycling.
INNE
Jaskr:
15
Język:
PL
Oprogramowanie
pmt99.04.270917
Czw
14:24
Czw
14:24
Czw
14:24
Czw
14:24
