Industrial Fiber Optics IF-FOM Скачать руководство пользователя страница 10

– 4 –

LED

The receptacle in the lower right corner of the front panel contains the LED optical light 
source used to launch energy into fi ber optic cables. The LED operates at a wavelength 
of 660 nm with a nominal optical power of 0.25 mW. The receptacle is a female “ST

®

” 

bayonet style fi ber optic connector, which also accepts the ST

®

 male plug used with 

plastic jacketed fi ber optic cables. Un-connectorized cables may also be inserted into this 
receptacle for measurements. As with the Detector, the plastic cap over the ST receptacle 
protects the internal LED from damage and dust. The cap must be removed prior to 
measurement and replaced when the test set is not in use.

Batteries

The Fiber Optic Test Set requires two 9-volt batteries (included) for operation. For shipping 
and storage purposes they have not been installed at the factory. To install or replace the 
batteries, follow the procedure in the section titled SERVICE AND MAINTENANCE.

Battery types suggested for use with this test set include standard, heavy duty, and alkaline 
9-volt batteries. Part numbers from major manufacturers are shown in Table 2. 

Note: The 

use of nickel-cadmium (NiCd) batteries is not recommended because their lower cell 
voltages may produce inaccurate readings.

Test Cable

A connectorized fi ber optic cable approximately one meter long is provided with the test 
set. Using the cable, a “self-test” procedure can be performed to verify proper instrument 
operation before making measurements. The cable is tested at the factory prior to shipment 
and a calibration value is supplied with the test set documentation. An adjustment 
procedure using this value compensates for aging of the built-in LED source. 

The cable is 

not intended for use as a patch cord and must be protected from damage to preserve its 
calibration value.

 

Table 2. Part numbers for popular batteries suitable for

the Fiber Optic Test Set

Manufac-

turer

Standard

Heavy Duty

Alkaline

Duracell

©

Not available

M9V

MN1604

Eveready

©

216

1222

522VP

Ray-o-Vac

©

1604

D1604

A1604

Содержание IF-FOM



























Отзывы: