background image

 25

ECU 12/2014 NEW

Chapter 6  Warranty

6.1  Limited Product Warranty

If any part of your Industrial Climate Engineering™ Environmental Control Unit (ECU) fails because 

of a manufacturing defect within eighteen months from the date of original shipment by ICE or within 

twelve months from the date of original start-up, whichever is the earlier date, ICE will furnish without 

charge, EXW Cordele, Georgia, the required replacement part. Any transportation, related service labor, 

diagnosis calls, filter, driers and refrigerant are not included. The owner must provide proof of the 

date of the original start-up. The owner’s registration card filed with ICE, the contractor’s invoice, the 

certificate of occupancy or similar document are examples of proof of the date of the original start-up.
  The responsibility of the Owner of the Equipment includes the following:
    1.   To operate the equipment according to the manufacturer’s instructions.

    2.   To provide easy accessibility for service.

    3.   To check and reset any circuit breaker(s) and/or disconnect(s) before calling for service.

    4.   To keep the unit clean and free of dirt.

    5.   To replace any filters as required.

    6.   To keep the outdoor coil section clean and free of leaves, paper, etc.

    7.   To pay the charges incurred when any of the above have not been done.

    8.   To pay for repair or replacement of any material or part other than those within the ICE unit 

     

or thermostat itself.

The owner of the product may ship the allegedly defective or malfunctioning product or part to ICE, at 

such owner’s expense, and ICE will diagnose the defect and, if the defect is covered under this warranty, 

ICE will honor its warranty and furnish the required replacement part. All costs for shipment and risk of 

loss during shipment of the product or part to ICE and back to the owner shall be the responsibility and 

liability of the owner. Upon written request by an owner, ICE may arrange for remote diagnosis of the 

allegedly defective or malfunctioning product or part but all costs for transportation, lodging and related 

expenses with regard to such diagnostic services shall be the responsibility and liability of the owner.
An owner requesting performance under this Warranty shall provide reasonable access to the allegedly 

defective or malfunctioning product to ICE and its authorized agents and employees.
This warranty only applies to products purchased and retained for use within the U.S.A, Canada and 

Mexico. This warranty does not cover damage caused by improper installation, misuse of equipment 

or negligent servicing.
THIS WARRANTY AND SERVICE POLICY CONSTITUTE THE EXCLUSIVE REMEDY OF ANY 

PURCHASER OF A ICE ECU AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR 

IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANT-

ABILITY OR FITNESS FOR USE, TO THE FULLEST EXTENT PERMITTED BY LAW. IN NO 

EVENT SHALL ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR USE 

EXCEED THE TERMS OF THE APPLICABLE WARRANTY STATED ABOVE AND ICE SHALL 

HAVE NO OTHER OBLIGATION OR LIABILITY. IN NO EVENT SHALL ICE BE LIABLE FOR 

INCIDENTAL OR CONSEQUENTIAL DAMAGES OR MONETARY DAMAGES.
THIS  WARRANTY  GIVES YOU  SPECIFIC  LEGAL  RIGHTS, AND YOU  MAY ALSO  HAVE 

OTHER RIGHTS WHICH
VARY FROM STATE-TO-STATE. Some states do not allow limitations or exclusions, so the above 

limitations and exclusions may not apply to you.

NEW

Содержание ECUA120



























Отзывы: