Instructions for installation and use
mode
select
A
D
B
C
E
1
2
3
4
Here I’m in command
Understanding the control panel
Making the right choice is important. And it’s easy.
Programme selector knob
Use this knob to select the wash
programme.
To select a programme, you
should turn the knob so that the
symbol/number of the desired
programme is in line with the
pointer on the knob.
Start /Reset
This button allows you to start
the selected wash programme
or to interrupt it.
If you press it briefly, the button
functions as Start, if you press
it for at least
3
seconds, then it
functions as Reset.
After the
Start
of the appliance,
moving the programme
selector knob will have no effect
whatsoever.
On-off
When button C is pressed, the
washing machine is switched
on, when it is not the machine
is switched off.
Turning the appliance off
does not cancel the selected
programme.
When the appliance is switched
on, all the symbols on the display
light up for at least
8
seconds,
after which only the ones that can
be selected will flash.
Detergent dispenser
It is divided into three
compartments:
1. Detergent for pre-wash;
2. Detergent for the main cycle wash;
3. Fabric conditioner.
The washing machine is
equipped with an extra
compartment
4 (provided as an
accessory) for the bleach, to be
inserted in compartment 1.
Display
All the options available are
displayed on the right-hand side.
Use the mode button to select
the desired option, and the rela-
tive symbol will begin flashing.
On the left-hand side, the value
or the status (On-Off) of the
selected option is displayed, and
you can modify it using the
select button.
To access the subsequent
option, press the mode button,
otherwise press button B to start
the wash cycle.
All the options available are listed
below.
Only options relevant to the
selected programme will be
displayed.
Temperature
The display indicates the maximum
temperature relating to the
programme set, which can be
reduced by pressing the select
button right down to cold wash
(Off).
This option is available on all
wash programmes.
Spin Variation
The display indicates the maximum
speed relating to the programme
The detergent dispenser with the
additional bleach compartment
is here.
3
set, which can be reduced by
pressing the select button right
down to its total exclusion
(Off).
During a wash cycle, the selection
of the spin cycle exclusion is
indicated by symbol
coming on.
This option is available on all wash
programmes except for number 11
and Drain.
Delay Timer
This allows you to delay the start
of the wash cycle by a minimum
of 1 to a maximum of 24 hours
by pressing the select button.
The enabling of the delayed
start is indicated by the symbol
coming on and staying on
until the wash cycle begins.
This option is not available on
the Draining and Spin cycle
programmes.
Easy Ironing
This function allows your washing
to come out of the machine without
creases, making it much easier to
iron.
The appliance optimises the
washing conditions according to
the type of fabrics that are being
washed.
It is enabled with programmes
3-5-6-7-8-11 and Rinse cycles.
To enable it, press the select
button until the On sign comes on.
In programmes 6-7-8-11 and Light
Rinse cycles, the wash cycle is
interrupted and the washing is left
to soak in water before the
appliance is drained. To complete
the cycle, press the select button.
During a wash cycle, the enabling
of this option is indicated by
symbol
coming on.
Note:
It must not be used with the
Stain Erase
option.
Rinsing level
This increases the efficiency of
the rinse. We recommend that you
use it when dealing with a full load
and a great amount of detergent.
There are three levels; press the
select button to select them.
Low
Medium
High
This option is available on
programmes 1-2-3-4-5-6-7-8
and Rinse cycles.
Stain Erase
(see page 7)
Thanks to this command, the
washing machine will carry out a
more intensive wash that
optimises the effectiveness of the
liquid additives, thus allowing more
resistant stains to be removed.
To use this, press the select
button until the On sign comes on.
During a wash cycle, the
selectionof this option is indicated
by symbol
coming on.
This option is available on
programmes 2-3-5-6-7-8-10 and
Rinse cycles.
Note:
It must not be used with the
Easy Ironing
option.
Wash Intensity
This allows you to modify the
characteristics of the selected
wash programme, according to
how soiled the washing is. There
are three levels; press the select
button to select them.
Low
Medium
High
This option is available on
programmes 1-2-3-5-6-7-8.
