AUS
3
* Only available in certain models
Fig. A
Fig. B
!
Some models can have their gas connection
inverted. It is important to make sure the safety
chain is always situated on the side which
corresponds to the hose holder (Fig. B).
Gas connection
T he cooker should be connected to the gas-supply
by a corgi registered installer. During installation of
this product it is essential to fit an approved gas tap
to isolate the supply from the appliance for the
convenience of any subsequent removal or
servicing. Connection of the appliance to the gas
mains or liquid gas
must be carried out
according to the
prescribed regulation in
force, and only after it
is ascertained that it is
adaptable to the type
of gas to be used. If
not, follow the
instructions indicated in
the paragraph headed
“Adaptation to different
gas types”. On some models the gas supply can be
connected on the left or on the right, as necessary;
to change the connection, reverse the position of the
hose holder with that of the cap and replace the
gasket (supplied with the appliance). In the case of
connection to liquid gas, by tank, use pressure
regulators that conform to the regulation in force. The
gas supply must be connected to the left of the
appliance. Be sure that the hose does not pass
through the rear of the cooker touching hot parts.
!
Make sure the supply pressure conforms with the
values shown in the table entitled “Caracteristics of
the burners and nozzles”. When the cooker is
When the cooker is
When the cooker is
When the cooker is
When the cooker is
installed between cabinets (recessed), the
installed between cabinets (recessed), the
installed between cabinets (recessed), the
installed between cabinets (recessed), the
installed between cabinets (recessed), the
gas connection must be effected by an
gas connection must be effected by an
gas connection must be effected by an
gas connection must be effected by an
gas connection must be effected by an
approved flexible hose with bayonet fitting
approved flexible hose with bayonet fitting
approved flexible hose with bayonet fitting
approved flexible hose with bayonet fitting
approved flexible hose with bayonet fitting
(BS 669 Current Edition). The gas inlet for
(BS 669 Current Edition). The gas inlet for
(BS 669 Current Edition). The gas inlet for
(BS 669 Current Edition). The gas inlet for
(BS 669 Current Edition). The gas inlet for
the cookers is a threaded G 1/2 gas female
the cookers is a threaded G 1/2 gas female
the cookers is a threaded G 1/2 gas female
the cookers is a threaded G 1/2 gas female
the cookers is a threaded G 1/2 gas female
f i t t i n g .
f i t t i n g .
f i t t i n g .
f i t t i n g .
f i t t i n g .
Connecting the gas supply
To make the connection, a flexible hose should be
used corresponding to the current gas regulations
which are:
• the hose must never be at any point in its lenght
in contact with the “hot” parts of the cooker;
• the hose must never be longer than 1,5 metre;
• the hose must not be subject to any tension or
torsional stress and it must not have any
excessively narrow curves or bottlenecks;
• the hose must be easy to inspect along its entire
length to check its condition;
• the hose must always be in good condition, never
attempt to repair.
!
The installation must comply with gas safety
(installation and use) regulations 1984. In all cases
for the above, by low, a qualified, corgi approved
engineer must be called for installation.
Electrial connection
Power supply voltage and frequency: 230-240V a.c.
50/60 Hz.
!!!!! The supply cable must be positioned so that it
never reaches at any point a temperature 50°C
higher than the room temperature. The cable must
be routed away from the rear vents. Should you
require it, you may use a longer cable, however, you
must ensure that the cable supplied with the
appliance is replaced by one of the same
specifications in accordance with current standards
and legislation.
Your appliance is supplied with a 13 amp fused plug
that can be plugged into a 13 amp socket for
immediate use. Before using the appliance please
read the instructions below.
WARNING - THIS APPLIANCE MUST BE
EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be used,
and the fuse cover re-fitted. If the fuse cover is lost,
the plug must not be used until a replacement is
obtained.
700 mm
HOT PARTS
HOOD
420
Min.
min.
650
mm. with hood
min.
700
mm. without hood
mm.
600
Min.
mm.
420
Min.
mm.
