8
TROUBLESHOOTING
PROBLEMS
POSSIBLE CAUSES
SOLUTIONS
Salt
indicator is lit
Salt reservoir is empty. (After refill the salt indica-
tor may remain lit for several wash cycles).
Refill reservoir with salt (for more information - see page 2).
Adjust water hardness - see table, page 2.
Rinse aid
indicator is lit
Rinse aid dispenser is empty. (After refill the rinse
aid indicator may remain lit for several wash
cycles).
Refill dispenser with rinse aid (for more information - see page 2).
The dishwasher
won’t start or does
not respond to
commands.
The appliance has not been plugged in properly. Insert the plug into the socket.
Power outage.
For safety reasons, dishwasher will not restart automatically when power
returns. Press the START/Pause button to resume the cycle.
The dishwasher door is not closed.
Vigorously push the door until you hear the “click”.
Cycle is interupted by door opening for > 4 sec.
Close the door and press START/Pause.
It does not respond to commands.
Switch off the appliance by pressing the ON/OFF button, switch it back on after
approximately one minute and restart the program. If problem persists, unplug
the appliance for 1 minute, then plug it back in.
The dishwasher
won’t drain.
The wash cycle has not finished yet.
Wait until the wash cycle finishes.
The drain hose is bent.
Check that the drain hose is not bent
(see INSTALATION INSTRUCTION).
The sink drain pipe is blocked.
Clean the sink drain pipe.
The filter is clogged up with food residues.
Clean the filter
(see CLEANING THE FILTER ASSEMBLY).
The dishwasher
makes
excessive noise.
The dishes are rattling against each other.
Position the crockery correctly
(see LOADING THE RACKS).
An excessive amount of foam has been produced.
The detergent has not been measured out correctly or it is not suitable for use
in dishwashers
(see FILLING THE DETERGENT DISPENSER).
Restart dishwasher
by pressing the DRAIN button
(see OPTIONS AND FUNCTIONS)
and run new
program without detergent.
The dishes are not
clean.
The crockery has not been arranged properly.
Arrange the crockery correctly
(see LOADING THE RACKS).
The spray arms cannot rotate freely, being hin-
dered by the dishes.
Arrange the crockery correctly
(see LOADING THE RACKS).
The wash cycle is too gentle.
Select an appropriate wash cycle
(see PROGRAMS TABLE).
An excessive amount of foam has been produced. The detergent has not been measured out correctly or it is not suitable for use in
dishwashers
(see FILLING THE DETERGENT DISPENSER).
The cap on the rinse aid compartment has not
been shut correctly.
Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged.
Clean the filter assembly
(see CARE AND MAINTENANCE).
There is no salt.
Fill the salt reservoir
(see FILLING THE SALT RESERVOIR).
The dishwasher
does not fill the
water. All LEDs
are blinking
rapidly.
No water in the water supply or the tap is closed. Make sure there is water in the water supply or the tap running.
The inlet hose is bent.
Make sure the inlet hose is not bent
(see INSTALLATION)
reprogram the dishwa-
sher and reboot.
The sieve in the water inlet hose is clogged; it is
necessary to clean it.
After having carried out the verification and cleaning, turn off and turn on the
dishwasher and restart a new program.
Dishwasher finishes
the cycle prema-
turely.
Drain hose positioned too low or siphoning into
home sewage system.
Check if end of drain hose is placed at correct height (see INSTALLATION).
Check for siphoning into home sewage system, install air admittance valve if
necessary.
Air in water supply.
Check water supply for leaks or other issues letting air inside.
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
•
Visiting our website:
docs.indesit.eu
•
Using QR Code
•
Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product’s
identification plate.
IEC 436
:
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.
The manufacturer ensures the availability of spare parts for at least 10 years after production date of this appliance.
400011410003B
12/2019 jk - Xerox Fabriano
