With the harness system Slope you bought is one of the most comfortable and functional training slope / passenger
harness, which is available on the market at present. Thank you for your confidence.
Please read this instructions carefully and consider, that Independence is not liable for accidents and damage, which
result from disregarding of this operating instructions.
Technical description:
The Slope is a harness for the use in a not motorized paraglider. The Slope is designed as a training slope harness /
tandem passenger harness and has no integrated rescue system container. It is tested according EN1651 and LTF
91/09.Certification No. Slope: EAPR GZ-0447/15.
technical datas
Slope
max. load
120 daN
harness weight
2,8 kg
hangpoint height
47 cm
protector system
Mousse Bag
Overview:
a) main suspension
b) lateral chest belt with
adjustment buckle
c) safety T-system with
chest belt buckle
d) Mousse bag protector
e) shoulder belt with
adjustment buckle
f) storage bag
g) leg belts
a)
a)
b)
c)
e)
d)
f)
g)
g)
e)
a)
a)
c)
g)
g)
a)
b)
f)
e)
d)
Adjustment possibilities:
Adjustment possibilities are existing at the shoulder belts, the chest belt, the lateral chest belts and the leg straps.
By the versatile adjusting possibilities of the Slope we recommend in any case that all adjustments and settings are done
in a simulator
before
the first flight to guarantee an optimal comfort.
The buckles of the chest and leg straps are secured against unintentional opening. To open these buckles you have to
push both buttons of the buckle at the same time.
Adjust the chest belt:
The chest belt is closed with Click-Lock-buckles. If the chest belt is closed, also the falling out safety device (Safe-T-
System) is closed. The Click-Lock buckles must be closed audibly! The length of the chest belt can be adjusted and
should not be tightened too much.
Adjusting the shoulder belts:
Please note that with correct adjusting the shoulder belts are felt with light pressure on the shoulders. With the shoulder
belts you adjust the harness on the pilot’s heigh, but also you adjust the seating position between upright and lying.
Adjusting the lateral chest belts:
Adjusting the lateral chest belts take place as the third step and offers on one side again the variation of the seating
position. On the other hand you adjust with the lateral chest belts the most comfortable seating position. During the
adjustment pay attention to the fact that the body load is distributed equal on shoulder belt and lateral chest belt.
Adjusting of the leg belts:
When you put the harness on, please take care that the Click-Lock-buckles are closed correct and audible. The leg belts
should be fastened tight but should leave your legs still enough space to move during take off and landing phase.
Operating notes:
Operation of the protector:
The Slope has a type certified back protector made out of a special foam, which is sewn in a nylon fabric cover (mousse
bag). Before every take off you have to check that the protector is completely filled up with air. Especially on low
temperatures and after long disuse of the protector (if compressed during storage) it may take a little longer to be inflated
completely.
During a hard landing the air inside of the protector systems will be compressed and the air will be deflated through the
seams of the nylon fabric cover. The resulting deceleration distributes the impact energy over a longer period and
protects the spine from extreme peak loads. The G-forces achieved in the type certification were very good. However,
even the best back protection does not guarantee the prevention of back injuries!!!
For this reason, the protector should not be used for unnecessary seat board landings. With every use the protector will
be less efficient and the effect of protection less - even if no damage is visible.
If a damage is visible the protector is not to be used anymore as well as after a hard landing!! In this case the protector
must be exchanged or repaired from an authorised dealer/workshop.
Before use of the harness the following points should be checked:
!
Outer shell of the protector and the entire belt system intact?
!
Protector fully inflated ?
!
All harness buckles properly closed and adjusted?
Maintenance / service life of the protector:
The protector is almost maintenance free. On Slope the protector should be checked if it is in right position and the foam is
fully inflated. The protector is, because of to the mounting position protected from mechanical damage.
Visible damage (holes, cracks) must be repaired, otherwise the outer shell can break during an impact with a loss of
damping.
After a hard landing with the use of the protector and if a damage is visible the protector must be repaired or exchanged by
the manufacturer or an authorised dealer/workshop.
Tandem flights:
The Slope is only suitable as a passenger harness.
