Incra TS III, Руководство пользователя

Страница: 8 / 12

 If you have not already done so, read the
operations section of your INCRA Jig Ultra owner’s manual
(pages 6 and 7) to familiarize yourself with the clamping and
micro adjust functions of the Ultra before continuing.
Slide Ultra carriage into base
Slide your Ultra’s carriage into the base and position the
fence mounting bracket approximately in line with the two
nearest rail mounting brackets. Lock the carriage in place.
See
 .
Loosely attach TS III fence
Place a
1
⁄
4
" flat washer on each of (2)
1
⁄
4
-20 x
1
⁄
2
" socket
head cap screws and insert the screws through the slotted
holes in the back of the fence mounting bracket. Loosely
attach the
1
⁄
4
-20 square nuts to the screws, then slide the
fence onto the square nuts as shown in
 . Position the
end of the fence nearest to the operator about 3
1
⁄
2
" in front of
the table’s edge. Do not tighten the fence mounting screws at
this time.
Attach fence glides
Place one of the supplied
3
⁄
4
" x 3" cardboard spacers
under each end of the fence as shown in
  and attach
the two fence glides to the rear of the fence using (4)
1 ⁄
4
- 20 x 1 ⁄
2
" socket head cap screws, 1 ⁄
4
" washers and
1
⁄
4
-20 square nuts. See
 . The glide with the black
thumbscrew mounts on the operator’s side of the saw. Align
the glides flush with the rails before tightening the fasteners.
Remove and save the cardboard spacers.
Tighten fence mounting screws
Unlock the carriage and slide the fence about 20" away
from the blade. Make sure the fence glides are still aligned
flush with the rails, then tighten the two fence mounting
screws. Take care not to raise or lower the fence mounting
bracket as you tighten the screws.
Engage anti-lift rail hooks
Lock the carriage clamp, then turn the black thumbscrew on the
front fence glide counterclockwise to lower the rail hook into the T-slot
on the rail. Look into the T-slot as you lower the hook. When the
hook passes the lip on the T-slot, slide the black thumbscrew toward
the table saw to position the hook under the lip. See
 . Now
turn the thumbscrew clockwise to raise the hook. The hook can be
adjusted to limit fence lift by turning the thumbscrew clockwise.
       
        
    
To engage the rear rail hook, walk to the rear of the saw and using a
3 ⁄
16
" hex tool, lower the hook into the T-slot on the rail. Slide the
fastener back to position the hook under the T-slot lip, then turn the
fastener clockwise to adjust the lift limit. Allow the fence to lift no more
than
1
⁄
32
".
          
FENCE ASSEMBLY
1
2
3
4
5
FIG. 15
Slide ULTRA
carriage into
base
Rail mounting
bracket
Position fence mounting
bracket approximately in line
with rail mounting brackets
and lock carriage in place
FIG. 16
Loosely attach TS III fence
1 ⁄
4
- 20
square nut
TS III fence
1 ⁄
4
" flat
washer
1 ⁄
4
- 20 x 1 ⁄
2
"
socket head
cap screw
FIG. 17
Attach fence glides
First: Place
cardboard spacers
under fence
Second:
Attach fence
glides
Cardboard spacer
Fence glide
DETAIL 17A
FIG. 18
Engage
anti-lift rail
hooks
Thumbscrew
Rail hook
NOTE:
When removing the TS III from your
table saw, always disengage the rail hooks from
the T-slot lip before lifting the TS III off the rails.
CAUTION:
Never adjust rear rail hook by reaching over
the saw. If an adjustment must be made, turn off the saw and
walk to the rear to make the adjustment.
1 ⁄
4
– 20 x 1 ⁄
2
" socket head cap screw
Fence mounting
bracket
Fence mounting bracket
Ultra carriage
1 ⁄
4
– 20
square nuts
INCRA Woodworking Tools & Precision Rules 8
1 ⁄
4
" washer
Fence glide
Rail