background image

®

Environmental Equipment, Inc.

 

IMR EX440 User Manual 

 

3632 Central Ave. St. Petersburg, FL 33711 – Phone: 727-328-2818 / 800-RING-IMR – Fax: 727-328-2826 – E-mail: [email protected] – Web: www.imrusa.com 

THE PRIDE OF THE COMPANY – MADE IN THE USA 

 

Page 

20

 of 

21

 

9.

 

Warranty 

IMR Environmental Equipment, Inc. states the following: 

IMR‚ as manufacturer hereby grants the following worldwide IMR warranty for an IMR analyzer purchased 
from an authorized dealer. 

1.

 

The IMR warranty shall entitle every IMR customer to demand a free replacement or repair of the defective 
parts from any IMR dealer authorized for the respective IMR unit. 

2.

 

The IMR warranty shall be granted on the factory new unit and shall commence on the date of the delivery 
of the original IMR unit to the customer. It shall last for a period of twelve months regardless of the type 
and the intensity of use and regardless of any change of owner, which may occur during this warranty 
period. 

3.

 

The IMR warranty shall refer to absence of faults with respect to the state of the art nature of the sold unit in 
terms of material and finish. The warranty for all parts fitted during the twelve-month warranty period shall 
end with the unit warranty. 

4.

 

After the establishment of a material or production fault by IMR or the authorized IMR dealer, the faults 
will be eliminated by means of free repair or replacement. Replaced parts shall become the property of IMR. 

5.

 

No warranty claims may be made for maintenance and setting work, cleaning or other utility materials 
required for the function of the unit and other wear parts unless they have a direct bearing on work 
performed under the warranty. 

6.

 

The terms and conditions for the acknowledgement of this warranty shall be the presentation of the fully 
completed warranty card, which must contain the confirmation from the authorized IMR dealer on its 
delivery and, if applicable, the prescribed maintenance work. 

7.

 

The IMR warranty shall only be applicable if 

7.1

 

The analyzer has been maintained in accordance with the instructions issued by the manufacturers and 
the operating instructions by an authorized IMR dealer. 

7.2

 

Only original IMR spare parts have been used for any repairs. 

7.3

 

The unit has been used properly, the operating instructions observed and the unit has not been used for a 
purpose other than the one for which it has been designed. 

7.4

 

The IMR unit has been left in its original design and meets the original IMR specifications. 

7.5

 

The fault is not due to external influences or use for a purpose other than the one for which it has been 
designed. 

7.6

 

Exclusively authorized IMR dealers have made repairs to the IMR unit. 

7.7

 

The IMR unit has been sent to an authorized IMR dealer immediately after the fault was discovered. 

8.

 

Warranty time for the analyzer, including electrochemical sensors is 12 months. 
 

 

Содержание EX440






















Отзывы: