background image

USER MANUAL

 

 

7

cleaning it. Only handle the power-cord by the plug. Never pull out the plug by 

tugging the power-cord. 

z

 

It is essential to connect the yellow/green conductor to earth. 

z

 

The electric connection, repairs and servicing must be carried out by a 

qualified employee. 

z

 

Do not switch the fixture on and off in short intervals as this would reduce the 

laser diode life. 

z

 

For replacement, please use fuses of same type and rating only. 

z

 

If the device has been exposed to drastic temperature fluctuation, do not 

switch it on immediately. The arising condensation water might damage your 

device. Leave the device switched off until it has reached room temperature.. 

z

 

Do not shake the device. Avoid brute force when installing or operating the 

device. 

z

 

When choosing the installation-spot, please make sure that the device is not 

exposed to extreme heat, moisture or dust. There should not be any cables 

lying around. You endanger your own and the safety of others! 

z

 

The minimum distance between the fixture and surrounding walls must be 

more than 50cm. 

z

 

Always fix the fixture with an appropriate safety-rope. Fix the safety-rope at 

the safety-rope only. 

z

 

The ambient temperature must be between 10

 to 40

z

 

Please use the original packaging if the device is to be transported. 

z

 

Please consider that unauthorized modifications on the device are forbidden 

due to safety reasons! 

 

 
 
 
 
 
 
 
 
 
 
 

 

CAUTION!  Operate the device only after having familiarized with 

its functions.

 

Do not permit operation by persons not 

qualified for operating the device. Most damages are 
the result of unprofessional operation   

CAUTION!    If this device will be operated in any way different to the 

one described in this manual, the product may suffer 
damages and the warranty word.

Содержание LSX-300SRGB
























Отзывы: