2
IMER
U.S.A. Inc.
MIX 60
Dear Customer, Congratulations on your choice of purchase: IMER
mixers are universal machines for MIX series: the MIX series mixers
are ideal for mixing dry or wet fine particle material (gypsum, cement,
ceramic tile adhesives, plaster, epoxy resin or proprietary mixed
products).
WORKING IN SAFETY
To work in complete safety, read the following instructions
carefully.
- This OPERATIONAND MAINTENANCE manual must be kept on
site by the person in charge, e.g. the SITE FOREMAN, and must
always be available for consultation.
- The manual is to be considered integral part of the machine and
must be kept for future reference (EN 292/2) until the machine is
disposed of. If the manual is damaged or lost, a replacement may be
requested from the saw manufacturer.
- The manual contains important information regarding site
preparation, machine use, maintenance procedures, and requests
for spare parts. Nevertheless, the installer and the operator must
both have adequate experience and knowledge of the machine prior
to use.
- To guarantee complete safety of the operator, safe operation and
long life of equipment, follow the instructions in this manual carefully,
and observe all safety standards currently in force for the prevention
of accidents at work (use of safety footwear and gloves in accordance
with S.I. N°3073 of 30/11/92).
Pay specialattention to warnings bearing the following symbol:
- MAKE SURE THAT SIGNS ARE LEGIBLE.
- It is strictly forbidden to carry out any form of modification to
the steel structure or working parts of the machine.
- IMER INTERNATIONAL declines all responsibility for non-
compliance with laws and standards governing the use of this
equipment, in particular; improper use, defective power supply, lack
of maintenance, unauthorised modifications, and partial or total failure
to observe the instructions contained in this manual.
1. TECHNICAL SPECIFICATIONS
2. DESIGN STANDARDS
The MIX 60 mixer has been designed and constructed in accordance
with the following standards:I.E.C.34.4; EN 60204-1; EN 392 (91/368
CEE).
3. NOISE EMISSION LEVEL
Operator exposure to sound emission levels (continuous sound
pressure levels equal to “A” weighting): the MIX 60 mixer noise level
during operation is measured at 65 dB(A).
4. OPERATION SAFETY
- The Imer MIX 60 cement mixer may only be used when fitted with
all required safetydevices which must be in perfect working condition.
- Keep well clear of the mixing tank during operation.
- Never connect MIX 60 to defective power lines.
- Make electrical connections on the construction site where they
will not be subject to damage.
- Lay power cables where they are not subject to risk of damage or
penetration of water into connectors. Onlyuse connectors electrically
protected against water sprays.
- Never connect the mixer to makeshift mains connections. If
necessary, consult qualified personnel.
- Repairs to electrical installations must onlybe carried out byqualified
technicians. Do not operate the mixer during maintenance or repairs.
- Observe all accident prevention and safety standards in the work
area.
5. ELECTRICAL SAFETY
The IMER MIX 60 is designed in compliance with EN 60204-1
standards and features water spray protection (IP54) and overload
protection.
Connect the MIXER to a suitable earthing plant on the site by means
of the relative earthing screw and a wire braid (or cable) with a
minimum size of 16 mm² (see fig.2).
The mixer is also fitted with a safety system comprising a limit switch
which shuts off machine operation whenever the reduction unit
support is lifted.
To reset, press the on/off pushbutton located in the electrical cabinet.
6. ASSEMBLY
- Position the frame and handle as shown in fig.3.
- Insert the link pin and the cotter pin and tighten.
- Insert the tank in the circular housing, ensuring that the four handles
fit onto the steel brackets. to prevent tank rotation during operation.
- Fit the safety grid, blade cover and screw the blade fully down
(fig.4).
7. TRANSPORT
- Warning: Always unplug the mixer from the power supply
before handling.
- MIX 60 is easily transported; use the handle indicated in fig.5 for
manual transport of the mixer.
- Never use the power cable to pull the machine.
- Never pull the power cable to unplug the machine.
8. INSTALLATION
- Remove the machine from the packaging.
- Install the mixer on level and solid ground
- Do not tilt the mixer during operation.
- When transporting the machine ensure that there are no obstacles
which may impair stability.
9. ELECTRICAL CONNECTION
- Ensure that mains voltage and cable sizes correspond to
specifications.
- MIX 60 is fitted with an ac motor which must be connected to a 115
V power supply with a cable fitted with suitable wear-resistant, anti-
crushing and weatherproof sheathing.
Cable length must not exceed 50 m.
- MIX 60 must only be used when fitted with all required safety
devices, which must be in perfect working condition.
1.
HANDLE
2.
SAFETY GRID
3.
FRAME
4.
REDUCTION UNIT SUPPORT
5.
BLADE ASSEMBLY
6.
TANK HOUSING
7.
GEARMOTOR
8.
LEGS
9.
TANK
10.
LIMIT SWITCH
11.
DATA PLATE
12.
TANK BRACKET
13.
WHEEL
14.
ELECTRICAL PANEL
Fig.1
Drum capacity
l
56
Drum diameter
mm
580
Paddle rpm
n°
55
Machine weight
Kg
30
Machine weight with packing
kg
32
Packing dimensions
mm
620x585x455
Wheel dimensions
mm
Ø100x20
Motor rating
Kw
0.55
Paddle rotation direction
clockwise
Absorbed current
A
9.2
Voltage
Volts
115
Frequency
Hz
60