background image

 

9 | 

P a g e

 

 

 

WastePro II 

ELECTRICAL CONNECTION 

 
All electrical work must be carried out by a qualified electrician and in accordance with the IEE Codes 
of Practice.  Examine the rating plate located on the rear panel (next to the mains inlet) to ensure 
that the characteristics shown are correct for the supply available.  The supply cable fitted is the 
minimum  required for connection to  the  mains supply. Site conditions  may  vary  with additional 
length of cable run, encapsulation in trunking, bunched with other cables etc. Should this apply, the 
electrician must alter the cable accordingly. 
 
The  WastePro  II  should  be  connected  to  a  suitable  3-phase  isolator  providing  at  least  3mm 
separation in all poles.   
 
The mains supply cord - cable colours and cable markings are shown in the table below: 
 
 
 
 
 
 
 

Warning: This appliance must be earthed. 

 
If the supply cord becomes damaged it must be replaced by qualified electrician in order to avoid a 
hazard. 
 
Examine  the  rating  plate  attached  to  the  machine  to  ensure  that  the  characteristics  shown  are 
correct for the supply available. The rating plate is located on the rear of the machine. The rating 
shown is for the WastePro II itself , the overall rating will be higher depending on the rating of the 
(existing) Macerator that is connected to the WastePro II and that should be taken into account for 
the electricity supply 
 
 

Sample Rating Plate 

 
 

 

 

 

Phase 

Cable Colour 

Cable Marking 

L1 

Brown 

L1 

L2 

Black 

L2 

L3 

Grey 

L3 

Earth 

Yellow/Green 

None 

Содержание F78/020























Отзывы: