IMC Networks iMcV-LIM 10/100 Скачать руководство пользователя страница 3

Страница: 3 / 16

iii

Table of Contents

FCC Radio Frequency Interference Statement ....................................................ii

Warranty............................................................................................................ii

About the iMcV-LIM 10/100 ..............................................................................1

Configuration Instructions ..................................................................................1

Installing an iMcV-LIM 10/100 ...........................................................................2

Unmanaged Modules.........................................................................................2

Modes of Operation...........................................................................................3

Troubleshooting Features ...................................................................................4

Link Fault Detection in FORCE Modes (LFD)......................................................5

LED Operation...................................................................................................6

Troubleshooting Features ...................................................................................7

Specifications .....................................................................................................8

IMC Networks Technical Support.......................................................................9

Fiber Optic Cleaning Guidelines.......................................................................10

Electrostatic Discharge Precautions...................................................................11

Certifications....................................................................................................12

Содержание iMcV-LIM 10/100

















Результаты поиска

Содержание iMcV-LIM 10/100

Отзывы:

Похожие инструкции для iMcV-LIM 10/100

Бренды по названию

Популярные бренды

IMC Networks iMcV-LIM 10/100, Руководство по эксплуатации

Результаты поиска

Содержание iMcV-LIM 10/100

Отзывы:

Похожие инструкции для iMcV-LIM 10/100

Бренды по названию

Популярные бренды