background image

6

 

 

NOTE 

Setting the duplex mode on iMcV-Gigabit (-10) modules is not required; auto-
negotiation functionality includes the duplex setting. 

FX Negotiation on iMcV-Gigabit (-10) 

iMcV-Gigabit (-10) modules include the FX Negotiation feature which negotiates 
duplex mode.  The default for this feature is disabled.  You must enable or disable 
this feature on both ends of the connection or you may have difficulty establishing a 
link.  If the device you are connecting to the iMcV-Gigabit module does not support 
auto-negotiation, disabling the feature on the iMcV-Gigabit module forces the link 
up.  The following table shows various configurations and the resulting link status: 
 

FX Auto-Negoitation on a 

Switch or iMcV-Gigabit 

FX Auto-Negotiation 

on iMcV-Gigabit (S5) 

Link Status 

iMcV-Gigabit-Off 

OFF 

Link 

iMcV-Gigabit-ON 

ON 

Link 

iMcV-Gigabit-Off 

ON 

No Link 

Switch-ON 

OFF 

No Link 

Switch-ON 

ON 

Link 

Switch-OFF 

OFF 

Link 

Switch-OFF 

ON 

Link 

Installing an iMcV Module 

iMcV Modules install in IMC Networks’ SNMP-manageable media converter chassis 
or in any MediaChassis.  To install an iMcV Module, remove the blank bracket 
covering the slot where the module is to be installed by removing the screws on the 
outside edges of the bracket.  Slide the iMcV Module into the chassis, via the 
cardguides, until the module is seated securely in the connector.  Secure the module 
to the chassis by tightening the captive screw.  Save any “blanks” removed during 
installation for future use if the configuration requirements change. 

Installation Tips 

When testing, IMC Networks recommends testing modules first in an unmanaged 
environment.  To do this, disable management (turn management off or remove the 
management module from the chassis), follow the unmanaged configuration 
instructions, then install the unit, connect the cables and test the LEDs.  When 
finished, re-activate management and configure the unit via the software.  Since 
single-strand fiber products use optics that transmit and receive on two  
different wavelengths, you must deploy single-strand fiber products in pairs, or  
connect two compatible IMC Networks single-strand fiber products.  For example, 
connect iMcV-Gigabit, TX/SSFX-SM1310-SC (which has 1310 xmt and 1550 rcv) to a 

Содержание iMcV-Gigabit

















Отзывы: