background image

2

 

Managed Modules 

To manage one or more IE-iMcV-MediaLinX TX/SFP Modules, an SNMP agent must 
be present in the chassis:  The iMediaChassis series requires an SNMP Management 
Module.  To configure Managed Modules, install the module first, and then configure 
using the management software. Module Details will provide information such as 
serial number, date code and part number as well as product-specific features.  

Configuration Control 

Some iMcV-Modules offer Configuration Control; labels on the front faceplate are 
identified as such. Configuration Control has been implemented to assist the end user 
by retaining the latest configuration regardless of how that configuration was 
implemented (via DIP Switch settings or SNMP). 

Historically, SNMP would override DIP Switch settings. If changes are made via DIP 
Switch settings, then hardware settings determine the configuration of the board.  If 
changes are made to the module via iView

2

, the SNMP settings determine the 

configuration of the board. 

 
Utilizing Configuration Control, the end user has three conditions under which the 
configuration of the iMcV-Module may be impacted: 

 

Installing an 

IE-iMcV-MediaLinX TX/SFP

 into a chassis already loaded with iMcV-

Modules or replacing an 

IE-iMcV-MediaLinX TX/SFP

 

The iMcV-Module will transfer its saved configurations. The 

IE-iMcV-

MediaLinX TX/SFP

 will not override the module’s configuration. 

 

Replacing the same type of iMcV-Module 

If the DIP Switch settings are the same as the settings on the removed iMcV-
Module, the IE-iMcV-MediaLinX TX/SFP determines the configuration 
settings. 

If the DIP Switch settings are different, then the configuration of the module 
is determined by the DIP Switch settings. (The settings are forwarded to the 
IE-iMcV-MediaLinX TX/SFP and the value is saved.) 

 

Installing a new model of iMcV-Module 

If another type of module is installed into the same slot in a chassis, the IE-
iMcV-MediaLinX TX/SFP clears the memory of the previous configuration 
for that slot; the settings of a new module are adopted and stored in the IE-
iMcV-MediaLinX TX/SFP. 

 
 
 
 
 

Содержание IE-iMcV-MediaLinX TX/SFP

















Отзывы: