manualshive.com logo in svg

Imagine Platinum VX, Инструкция по установке и эксплуатации

Поделиться
Скачать
Imagine Platinum VX Скачать руководство пользователя страница 24

Platinum™ VX 
Installation and Operation Manual 

 

Platinum VX Frame 

 

© 2016 Imagine Communications Corp.

          

Proprietary and Confidential.

 

Version 1.2 | Page 24 

 

Platinum VX Frame 

The following variants are available: 

 

1 RU Frame (PV-16X16-FR-1) (on page 

24

) 

 

1 RU Frame (PV-CQ16-FR-1) with Clean and Quiet Switching (on page 25) 

 

2 RU Frame (PV-48X48-FR-2/PV-72X72-FR-2/PV-72SFP-FR-2) (on page 26) 

 

4 RU Frame (PV-FR-4) (on page 28) 

 

8 RU Frame (PV-FR-8) (on page 30) 

 

1 RU Frame (PV-16X16-FR-1) 

The 1 RU Platinum VX frame is orderable as a complete unit. It offers 16 HD-BNC inputs and 16 outputs 
via built in connectors on the rear panel.  

In addition, there are 16 SFP (small form-factor pluggable) cages on the frame, providing an additional 
16 inputs and 16 outputs. You add the hot-pluggable SFP modules to create versatile solutions that fit 
the specific application by ordering individual SFPs and sliding them into the cages built into the frame. 
All the supported SFP modules are dual port except for the HDMI SFP module. For supported SFP 
modules and specifications, see Supported SFP Types (see "Supported SFP Specifications" on page 71). 

Table 4:

 

1 RU Platinum VX Frame Modules and Matrix 

Part Number 

Frame 
Type 

Number of HD-BNC 
Inputs/Outputs 

Number of SFP cages for 
additional 
inputs/outputs 

Total Matrix Size 

PV-16X16-FR-1

 

1 RU 

16x16 

16x16 

16x16 (electrical only) 
32x32 (electrical and SFP) 

 

Figure 5:

 

1 RU Platinum VX Frame - Front View 

 

Figure 6:

 

1 RU Platinum VX - Rear View 

Содержание Platinum VX

































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды