Imagine DQS6800+ Скачать руководство пользователя страница 42

Страница: 42 / 84

DQS6800

Installation and Operation Manual

Chapter 3: Operation

Changing Parameter Settings

You can change parameter settings at the card edge for DQS6800

modules, or you can change the parameter settings, view read-only
parameters, view alarms, and adjust alarm settings using CCS software.
See the following topics for more information:

•

“Changing Parameter Settings Using Card-Edge Controls” on
page 28

•

“Changing Parameter Settings Using Software” on page 30

Changing Parameter Settings Using Card-Edge Controls

Follow these steps to change the DQS6800

parameter settings:

1. Rotate the hex switch (mode select rotary switch) to “0.”

2. Once the hex switch is set to “0,” toggle the navigation switch up or

down to select a bank.

View the control LEDs next to the navigation toggle switch to see
which bank is currently selected. (See

Table 3-2

See

Table 3-4 on page 33

to view the various banks, hex switch

positions, and corresponding parameter options and values.

Table 3-2. Selected Bank as Indicated
by Control LEDs

LED 3

LED 2

LED 1

LED 0

Bank Number

Off

Содержание DQS6800+





















































































Результаты поиска

Содержание DQS6800+

Отзывы:

Бренды по названию

Популярные бренды

Imagine DQS6800+, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DQS6800+

Отзывы:

Бренды по названию

Популярные бренды