imaage dynamics Q1200.1 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 9

imaage dynamics Q1200.1 Скачать руководство пользователя страница 4

- 3 -

PLANNING and INSTALLING YOUR SYSTEM (continued)

STEPS FOR AMPLFIER INSTALATION-

The following represents the steps for a typical amplifier installation, using
an aftermarket source unit or OEM source Interface. Not all installations are
the same and different procedures may be required. If you have any ques-
tions, please contact your authorized Image Dynamics dealer for assistance.

1-

Disconnect the negative battery connection and secure it to prevent acc-

idental re-connection during installation. This is a required step!

2-

Run power wire (minimum 4 AWG) from the battery to the amplifier, taking

care to route it in such a way that it will not be damaged and will not interfere
with vehicle operation. Use 2 AWG or 1/0 AWG power wire if multiple are being
installed.

3-

Connect power wire to the positive battery post. Fuse the wire within 18

inches wire length of the positive battery post. This fuse protects the vehicle in
the case of a short circuit. Do not install the fuse until the power wire has been
connected to the amplifier.

4-

Run RCA cables and remote turn-on wire from the source unit to the ampli-

fier.

5-

Run speaker wire from the speaker locations to the amplifier.

6-

Find a good, solid metal grounding point close to the amplifier, remove all

paint and sound deadener to bare metal, then connect the negative power wire
using a minimum of a #12 screw or 1/4” bolt. Use minimum 4 AWG power wire
from the amplifier to the ground connection point. In most vehicles, it is neces-
sary to upgrade the battery to chassis ground wire to a minimum of 4 AWG.

7-

Securely mount the amplifier using supplied hardware.

8-

Connect the positive and negative power wires to the amplifier. A fuse near

the amplifier is not recommended.

9-

Connect the remote turn-on wire to the amplifier.

10

- Connect the RCA cables to the amplifier.

11-

Connect the speaker wires to the amplifier.

12-

Carefully select the proper settings for the Amplifier according to the needs

of the system.

13-

Install power wire fuse and reconnect the negative battery post terminal.

14-

Turn on the system at a low level to check that the amplifier is configured

correctly. Resist the temptation to crank it up until you have verified the control
settings.

15-

Make necessary adjustments to the input sensitivity controls to obtain the

right overall output and the desired balance in the system.

16-

Enjoy your system.

«
...
2
3
4
5
6
...
»

Содержание Q1200.1










Отзывы:

Нет отзывов