manualshive.com logo in svg

Ikelite SLR-DC Housing, Инструкция по эксплуатации

Поделиться
Скачать
Ikelite SLR-DC Housing Скачать руководство пользователя страница 8

On the housing back is a switch

for setting the DS Strobe ID. Set

the switch to the Model of DS

Strobe being used.

When using dual strobes of

different models such as a

DS51 and a DS161, set the ID

switch to DS51 or the smaller

strobe.

8

DS

DS

125

50

51

160

161

ikelite

Set DS Substrobes

     to TTL Mode

200

Setting the Conversion Circuitry Strobe ID Switch 

Strobe ID

Switch

Housing Conversion Circuitry

This housing contains Ikelite designed and patented Conversion

Circuitry. Once attached, turn the strobe on first before turning on the

camera.

When used with Ikelite DS Strobes the Conversion Circuitry provides

real Nikon iTTL flash exposure with over and underexposure

compensation from +1 1/3 to - 1 1/3 f-stops in 1/3 stop increments.

The Conversion Circuitry also offers Manual exposure control with 3 1/2

f-stops of underexposure control in 1/2 stop increments.

The Conversion Circuitry is powered by the Ikelite DS Strobe when

connected to the housing with the 4103.51 single or 4103.52 dual sync

cord. When using two strobes with the dual sync cord, the primary

strobe connected to the cord without the red band, must be turned on to

power the Conversion Circuitry. Always keep both strobes connected to

your dual sync cord underwater. Do not exchange your secondary

strobe for a dust cap which may not be waterproof.

Содержание SLR-DC Housing

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды