8
D
Diiffffuusseerr &
& D
Deefflleeccttoorr IInnssttaallllaattiioonn
Housing shown with
deflector installed.
Deflector
U
Ussiinngg FFllaasshh
U
Ussiinngg tthhee CCaam
meerraa’’ss BBuuiilltt--iinn FFllaasshh..
If you do not have an external flash the camera’s built-in flash
can be used. See Diffuser instructions.
NOTE: The camera’s built-in flash cannot be used with optional
Wide-angle lenses.
9
D
Diiffffuusseerr aanndd D
Deefflleeccttoorr ccoonntt..
A diffuser and deflector are
included with the housing. The
diffuser is white transparent
plastic. The deflector is also white
but is not transparent and has a
decal on the front.
To install the diffuser or deflector
spread the port clamp at the spring
end and slide over the lens port.
The white plastic should be placed
in front of the camera flash. The
port clamp should be pushed back
against the front of the housing.
D
Diiffffuusseerr
The diffuser should be installed when using the camera’s built in
flash. When shooting with the camera’s built-in flash at
approximately 2 feet (0.6 m) or less, the lens port on the
housing blocks a portion of the light from the camera’s built-in
flash, creating a shadow in the lower left of the photo. To
eliminate the shadow zoom the lens between 1/3 and 1/2 of its
full telephoto range.
(You can test this above water)
D
Deefflleeccttoorr
The deflector should be installed when using an external strobe
such as the DS51 or DS125 Substrobe and EV Controller. The
deflector will redirect the camera’s flash to the EV Controller
which controls the external strobes output.
Diffuser/
Deflector
material
Port Clamp
Spring
Spread to Install
10
LLeennss PPoorrtt
Treat the glass in the lens port as a camera lens. After use, rinse
and gently dry the lens port to avoid water spotting. To clean
use a mild soap solution or lens cleaner.
Do not use alcohol or window cleaner on the Lens Port.
The Lens Port will accept (2) Wide-Angle Adapters. The Wide-
Angle Adapter #9306.80 which is required to mount the Inon
UWL-150AD Bayonet style wide-angle lens. The Wide-Angle
Adapter 9306.81 is required to mount the following Wide-Angle
Lenses, Inon UWL-100, Sea&Sea #58070 and Ep0que DCL-20
screw thread (67mm) style wide-angle lenses.
These lenses can be secured onto the Wide-Angle Adapter
above or below water as they are designed to have water
between the front of the port and the accessory lens. Make sure
no air bubbles are trapped between the port and the accessory
lens. Any vignetting that occurs can be eliminated by zooming
the camera lens slightly. The camera’s built-in flash cannot be
used with wide angle
lenses. The front of the
lenses are so large they
block the camera’s flash.
To properly light subjects
when using a wide angle
lens an external strobe
should be used. Due to
the wide-angle of
coverage of these lenses,
the DS125 Substrobe is
recommended or two
DS51 Substrobes.
Wide-Angle Lens
Wide-Angle Adapter
11
O
Oppttiioonnaall AAcccceessssoorriieess
BBaacckk O
O’’rriinngg
##00111100
O’rings last for several years if properly maintained. (See
maintenance) Always carry a spare.
U
URR//PPrroo FFiilltteerr
##66444411..3322
The UR/Pro underwater color correcting filter is designed to
restore some of the warm colors filtered out by the water. For
available light use only, not recommended for use with flash.
D
Duuaall H
Haannddllee TTrraayy
##99552233..1122
A Dual Handle Tray is available. The Dual Handle Tray provides
a second access point for mounting a second strobe.
SSuubbssttrroobbee PPaacckkaaggeess AAvvaaiillaabbllee
#3944.45 DS51, Sync Cord, Strobe Arm Is
#3944.51 DS51, Sync Cord, Strobe Arm SA-100R
#3944.75 DS125, Sync Cord, Strobe Arm SA-100R Smart Charger
U
Ussiinngg EExxtteerrnnaall FFllaasshh iinn M
Maannuuaall M
Mooddee
To use any power settingbs on an external flash in it’s manual
mode the camera’s flash mode must be set to “Slave Mode”.
In the camera’s menu set-up go to flash mode and select
“Slave Mode”. If Slave Mode is not selected most images will
be underexposed.
