10
O
Oppttiioonnaall AAcccceessssoorriieess
BBaacckk oo--rriinngg
#
#00110099
O-rings last for several years if properly maintained. (See
maintenance) Always carry a spare in case o-ring becomes
damaged or lost.
W
Wiiddee--AAnnggllee AAddaapptteerr
#
#99330066..8800
Required to mount Inon UWL-150AD Bayonet style wide-angle lens.
W
Wiiddee--AAnnggllee AAddaapptteerr
#
#99330066..8811
Required to mount Ikelite W-20 and other Screw Thread
(67mm) style wide-angle lenses.
U
URR//PPrroo FFiilltteerr ((BBlluuee W
Waatteerr))
#
#66444411..3322
The UR/Pro underwater color correcting filter is designed to
restore some of the warm colors filtered out by the water. For
available light use only, not recommended for use with flash.
GGrreeeenn W
Waatteerr FFiilltteerr
#
#66444411..7722
Enhances contrast and alters the color of green water to
give our subject a rich, natural tone. For available light
only, not recommended for use with flash.
TTrraayy w
wiitthh RReelleeaassee H
Haannddllee
#
#99552233..3311
Tray and Release Handle is required
to mount external Substrobes.
IIkkeelliittee W
W--2200 W
Wiiddee--AAnnggllee LLeennss
#
#66442200
Wide-Angle lenses allow you to capture more of the scene and
get closer to your subject which results in clearer images and
more vivid color. Can be installed or removed underwater for
maximum versatility. (Note: some housings may require an
adapter, see instructions.)
12
9
M
Maaiinntteennaannccee
The Ikelite Digital Housing should be given the same care and
attention as your other photographic equipment. In addition to
normal maintenance we recommend that the housing be returned
to Ikelite periodically to be checked and pressure tested.
1. D
Doo N
Noott leave the camera and housing in direct sunlight for
prolonged periods. Heat may damage the camera.
2. D
Doo N
Noott ship the camera in the housing.
3. Before using the housing, always check the tightness of the sseett
ssccrreew
w in each control knob.
Check each ccoonnttrrooll ggllaanndd to make sure they are tight. There is
a slight chance that either could vibrate loose during travel.
4. Keep the back o'ring clean and lightly lubricated. To lubricate
remove the o'ring from the back. Put a small amount of lkelite
lubricant on your fingers. Draw the o'ring through your fingers
to apply a light coating of lubricant. Only apply enough
lubricant to make the o'ring feel slick. D
Doo N
Noott ssttrreettcchh tthhee oo''rriinngg.
This light coating of lubricant will help to keep the o'ring from
drying out and will help to show a dark sealing line when the
housing back is properly sealed.
5. Keep the area where the o'ring fits and the sealing surface of
the housing clean.
6. Rinse the housing exterior in fresh water after each salt water
use. Dry with a soft cloth. Dry lens port to eliminate spotting.
After several uses in salt water soak the housing in a mild soap
solution, rinse and dry before storage. When storing the
housing, remove the back o'ring, lightly lubricate and place in a
plastic bag. Place the plastic bag with o'ring inside the housing
for safe keeping.
CCAAU
UTTIIO
ON
N
N
Neevveerr uussee sspprraayy lluubbrriiccaannttss aass tthhee pprrooppeellllaanntt iinnggrreeddiieenntt ccaann
c
caauussee tthhee ppllaassttiicc hhoouussiinngg ttoo ccrraacckk..
D
Diiffffuusseerr aanndd D
Deefflleeccttoorr ccoonntt..
A diffuser and deflector are
included with the housing.
The diffuser is white
transparent plastic. The
deflector is also white but
is not transparent.
To install the diffuser or
deflector spread the port
clamp at the spring end and
slide over the lens port. The
white plastic should be
placed in front of the camera
flash. The port clamp should
be pushed back against the
front of the housing.
D
Diiffffuusseerr
The diffuser should be installed when using the camera's built
in flash. When shooting with the camera's built-in flash at
approximately 2 feet (0.6 m) or less, the lens port on the
housing may block a portion of the light from the camera's
built-in flash, creating a shadow in the lower left of the photo.
If this occurs, zoom the lens slightly to eliminate the shadow.
(You can test this above water)
D
Deefflleeccttoorr
The deflector should be installed when using an external strobe
such as the DS51 or DS125 Substrobe and EV Controller. The
deflector will redirect the camera's flash to the EV Controller
which controls the external strobes output.
Diffuser/
Deflector
material
Port Clamp
Spring
Spread to Install
This edge
against
housing
11
SSuubbssttrroobbee PPaacckkaaggeess aavvaaiillaabbllee
#3944.47 SubStrobe DS51 with EV Controller & Strobe Arm
#3944.54 SubStrobe DS51 with EV Controller & Ball Socket Arm
#3944.77 SubStrobe DS125 with EV Controller & Ball Socket Arm
Substrobe
DS125
SSuubbssttrroobbee D
DSS112255
The Substrobe DS125 covers the
equivalent of a 18mm lens, 100
degrees. It is the ideal choice
when using accessory wide angle
lenses greater than 28mm.
Substrobe
DS51
EV Controller
EV Controller
SA-100R
Arm
SA-100R
Arm
SSuubbssttrroobbee D
DSS5511
The Substrobe DS51 covers the
equivalent of a 28mm lens. It is
the ideal choice when using only
the camera lens or the camera
lens with a macro accessory lens.
O
Oppttiioonnaall AAcccceessssoorriieess CCoonnttiinnuueedd
