manualshive.com logo in svg

Ikelite 6170.50, Инструкция по эксплуатации

Поделиться
Скачать
Ikelite 6170.50 Скачать руководство пользователя страница 8

STEP 2 - Opening the Housing 

8

Lid Snaps have a 

Lock

.

1. Push Lid Snap Locks forward and lift as shown.

Open opposing Lid Snaps simultaneously. Keep

pressure on the Lid Snaps so they do not fly open

quickly. 

Some Lid Snaps have a lot of spring tension

once they go over center, so keep a firm grip on

each Lid Snap. Lid Snaps may also be opened one at a time. 

2.

Remove the Housing Back. 

Push Forward

Lid 

Snap 

Lock

Lift

STEP 3 - Camera Installation/Removal

    CAUTION:

Do not cross thread or overtighten the Mounting Tray Bolt as you may 

damage the camera tripod socket threads.

STEP 1 -   Initial Camera Setup

- continued

If close-up images are 

overexposed

, adjust aperture setting and/or use

“-”       Exposure Compensation and/or back away, zoom in, and then
reshoot. When using an AF35 strobe or manual controller, turn the power
down.

** All camera user settings not listed should be set to the user’s

preference.

1. Pull out on each housing control until it stops. This will get the controls 

out of the way for installation of the camera.

2. Remove camera lanyard from camera if attached. 

3. Slide the Mounting Tray out of the camera Mounting Plate. Use the

index and middle fingers of each hand to pull the Tab section of the

Mounting Tray away from the Mounting Plate, 

Diagram A, page 9

. 

Содержание 6170.50

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды