ikelite.com
46064-NT2-Nikon-TTL-Hotshoe-1-1017
©
2017 Ikelite Underwater Systems
Manual Hotshoe Removal
Depress Hotshoe Connector Tab and pull Connector Ends apart as
shown, Diagram A, front page.
Hotshoe Installation - Diagram B, Front Page
1.
Line up Hotshoe Connector End with Bulkhead Connector End and
push together. Tab will click into place and be in the “up” position
when properly connected.
2.
Slide Hotshoe forward into camera mount until Hotshoe stops.
Make sure Hotshoe is all the way forward in camera mount to
assure a good connection.
3.
To confirm TTL operation, connect the strobe and set the camera at
its widest aperture, such as f/2.8. Trip the shutter while the camera
and strobe are aimed at a very close, well-lit subject. The strobe
should produce only a small blip of light. Repeat this with the lens
covered and the strobe should produce a full power flash.
Important Information
A DS-series strobe(s), TTL Sync Cord, and an Ikelite TTL Converter
must be used in conjunction with the Nikon TTL Hotshoe (yellow
band) to achieve TTL exposure. Using a TTL Hotshoe without a
TTL Converter may damage your camera.
To trigger strobe(s) manually use the Hotshoe (not banded) that
was included with the housing.
To replace the Hotshoe, depress the Hotshoe Connector Tab,
Diagram B, front page, and pull away from Bulkhead Connector.
ikelite.com
46064-NT2-Nikon-TTL-Hotshoe-1-1017
©
2017 Ikelite Underwater Systems
Manual Hotshoe Removal
Depress Hotshoe Connector Tab and pull Connector Ends apart as
shown, Diagram A, front page.
Hotshoe Installation - Diagram B, Front Page
1.
Line up Hotshoe Connector End with Bulkhead Connector End and
push together. Tab will click into place and be in the “up” position
when properly connected.
2.
Slide Hotshoe forward into camera mount until Hotshoe stops.
Make sure Hotshoe is all the way forward in camera mount to
assure a good connection.
3.
To confirm TTL operation, connect the strobe and set the camera at
its widest aperture, such as f/2.8. Trip the shutter while the camera
and strobe are aimed at a very close, well-lit subject. The strobe
should produce only a small blip of light. Repeat this with the lens
covered and the strobe should produce a full power flash.
Important Information
A DS-series strobe(s), TTL Sync Cord, and an Ikelite TTL Converter
must be used in conjunction with the Nikon TTL Hotshoe (yellow
band) to achieve TTL exposure. Using a TTL Hotshoe without a
TTL Converter may damage your camera.
To trigger strobe(s) manually use the Hotshoe (not banded) that
was included with the housing.
To replace the Hotshoe, depress the Hotshoe Connector Tab,
Diagram B, front page, and pull away from Bulkhead Connector.
ikelite.com
46064-NT2-Nikon-TTL-Hotshoe-1-1017
©
2017 Ikelite Underwater Systems
Manual Hotshoe Removal
Depress Hotshoe Connector Tab and pull Connector Ends apart as
shown, Diagram A, front page.
Hotshoe Installation - Diagram B, Front Page
1.
Line up Hotshoe Connector End with Bulkhead Connector End and
push together. Tab will click into place and be in the “up” position
when properly connected.
2.
Slide Hotshoe forward into camera mount until Hotshoe stops.
Make sure Hotshoe is all the way forward in camera mount to
assure a good connection.
3.
To confirm TTL operation, connect the strobe and set the camera at
its widest aperture, such as f/2.8. Trip the shutter while the camera
and strobe are aimed at a very close, well-lit subject. The strobe
should produce only a small blip of light. Repeat this with the lens
covered and the strobe should produce a full power flash.
Important Information
A DS-series strobe(s), TTL Sync Cord, and an Ikelite TTL Converter
must be used in conjunction with the Nikon TTL Hotshoe (yellow
band) to achieve TTL exposure. Using a TTL Hotshoe without a
TTL Converter may damage your camera.
To trigger strobe(s) manually use the Hotshoe (not banded) that
was included with the housing.
To replace the Hotshoe, depress the Hotshoe Connector Tab,
Diagram B, front page, and pull away from Bulkhead Connector.
ikelite.com
46064-NT2-Nikon-TTL-Hotshoe-1-1017
©
2017 Ikelite Underwater Systems
Manual Hotshoe Removal
Depress Hotshoe Connector Tab and pull Connector Ends apart as
shown, Diagram A, front page.
Hotshoe Installation - Diagram B, Front Page
1.
Line up Hotshoe Connector End with Bulkhead Connector End and
push together. Tab will click into place and be in the “up” position
when properly connected.
2.
Slide Hotshoe forward into camera mount until Hotshoe stops.
Make sure Hotshoe is all the way forward in camera mount to
assure a good connection.
3.
To confirm TTL operation, connect the strobe and set the camera at
its widest aperture, such as f/2.8. Trip the shutter while the camera
and strobe are aimed at a very close, well-lit subject. The strobe
should produce only a small blip of light. Repeat this with the lens
covered and the strobe should produce a full power flash.
Important Information
A DS-series strobe(s), TTL Sync Cord, and an Ikelite TTL Converter
must be used in conjunction with the Nikon TTL Hotshoe (yellow
band) to achieve TTL exposure. Using a TTL Hotshoe without a
TTL Converter may damage your camera.
To trigger strobe(s) manually use the Hotshoe (not banded) that
was included with the housing.
To replace the Hotshoe, depress the Hotshoe Connector Tab,
Diagram B, front page, and pull away from Bulkhead Connector.
