Ikegami Tsushinki Co., Ltd.
INSTRUCTION MANUAL
MODEL
ICD-505
COLOR CAMERA
OUTDOOR USE WARNING
WARNING – TO PREVENT FIRE OR
ELECTRIC SHOCK, DO NOT
EXPOSED THIS APPLIANCE TO
RAIN OR MOISTURE.
Ikegami Electronics (U.S.A.), Inc.
37 Brook Avenue, Maywood, New Jersey 07607, U.S.A.
Phone: (201) 368-9171, FAX 201-569-1626
Ikegami Electronics (Europe) GmbH
Ikegami Strasse 1, 41460 Neuss 1, F.R. Germany
TEL. 02131-123-0/FAX 02131-102820
Ikegami Electronics (Europe) GmbH U.K. Branch
Unit E1 Cologne Court Brooklands Close, Windmill Road
Sunbury-on-Thames Middlesex TW16 7EB, UK
TEL. 01932-769700/FAX 01-92-769710
K32567-1
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
NOTE:
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
CAUTION;
ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY
APPROVED BY THE PART RESPONSIBLE FOR COMPLIANCE COULD
VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT.
NOTA:
Este equipo ha sido probado y ha demostrado cumplir con los límites
establecidos para los dispositivos digitales de la clase A, en conformidad con
el Apartado 15 de los Reglamentos de la FCC. Estos límites han sido
diseñados para proporcionar una protección razonable contra la interferencia
perjudicial si el equipo se utiliza en un entorno comercial. Este equipo genera,
utiliza y puede radiar energía radioeléctrica, y, si no se instala y usa de
acuerdo con las instrucciones, puede causar interferencias perjudiciales en
las comunicaciones por radio, en conformidad con el Apartado 15 de los
Reglamentos de la FCC. Estos límites han sido establecidos para
proporcionar una protección razonable, el usuario tendrá que corregir la
interferencia corriendo él a cargo de los gastos pertinentes.
PRECAUCIÓN;
CUALQUIER CAMBIO O MODIFICACIÓN QUE NO HAYA
SIDO APROBADO EXPRESAMENTE POR LA PARTE RESPONSABLE
PODRÍA ANULAR LA AUTORIZACIÓN QUE TIENE EL USUARIO PARA
UTILIZAR EL EQUIPO.
El signo de exclamación en el interior de un triángulo equilátero tiene la
finalidad de avisar al usuario de la presencia de instrucciones de utilización y
mantenimiento (servicio) importantes en el manual que acompaña al aparato.
Thank you very much for your wise choice of the Ikegami Color CCD
Camera. Please carefully read this Instruction Manual to keep your
camera at full capacity.
Muchísimas gracias por haber elegido la cámara CCD en color de
Ikegami. Lea cuidadosamente este manual de instrucciones para
mantener su cámara en las mejores condiciones de funcionamiento.
E-1.
Handling precautions
(1) Do not open the case of camera and never touch inside, where
precision parts are assembled. A trouble or accident may result.
(2) Do not install the unit where it is exposed to water splash, high
humidity and heavy dust. Internal parts may be damaged.
Preferably use the camera at ambient temperatures of -10 to +50
°
C.
(3) Be very careful not to drop or shock the camera.
(4) Never touch the CCD surface.
E-2.
General
The ICD-505 are single CCTV cameras that employ a 1/3-inch CCD
(Charge Coupled Device) respectively, with 380,000 picture elements.
The units feature high resolution, high sensitivity and high picture
quality, and are equipped with many functions: back-light
compensation, automatic electronic shutter, automatic iris control and
others. The cameras are best suited for general-purpose monitoring.
E-3.
Features
(1) Digital processing
(2) High-quality picture and high resolution
(3) High-sensitivity design
(4) Equipped with back-light compensating function
(5) 2-way automatic iris controlling function
(6) Automatic white balance
(7) AES (Automatic Electronic Shutter)
(8) Flange focal distance adjusting mechanism
(9) The camera measures 53mm in depth in order to fit in a limited space.
E-4.
Names of parts and
their functions
English
CLASS 2
AES
BLC
AGC
OFF
OFF
OFF
VIDEO
D C
L L
INT
VIDEO OUT
IRIS LEVEL
LL PHASE
POWER
LENS
MAX40mA
Digital Process
COLOR CAMERA
CO
LO
R
CA
ME
RA
MO
DE
L
IC
D–
50
5
TY
PE
AC
24
V 6
0H
z 3
. 6
W/D
C12V 3. 6W RE
V.
SE
R.
N
O.
DA
TE
I K
EG
AM
I
TS
US
HIN
KI
C
O.,
L
TD
.
MA
DE
I
N
JA
PA
N
FD
N
DC12V3.6W
- +
AC24V60Hz3.6W
1
7
8
9
10
11
13
2
12
5
3
14
4
6
③
Holder mounting screw holes
These holes are used to fix the camera on the camera holder. They
are also applicable to general tripods.
Note:
To attach the camera on a tripod or a camera holder, be
sure to use mounting screws.
(1/4" -20UNC) that are shorter than 5.5 mm.
④
Auto iris lens connector
The connector is specifically used to connect the auto iris lens. Use the
optional auto iris lens control connector plug (E4-191J-150 or equivalent).
• For the video type auto iris lens
Set the lens selector switch to VIDEO position.
— Connector cable leads —
1. Red (power)
2. Not used
3. White (video)
4. Black (shielded)
* Dress the tip of the green lead to prevent a short-circuit.
• For the DC type auto iris lens
Set the lens selector switch to DC position.
— Connector cable leads —
1. Damping coil (-)
2. Damping coil (+)
3. Driving coil (+)
4. Driving coil (-)
* Connect the leads as shown above.
Refer also to the instructions of the lens.
⑤
Iris level control (IRIS LEVEL)
This control adjusts the sensitivity with a DC iris lens in use.
⑥
Line lock phase control (LL PHASE)
This control adjusts the phases of the video output and the power line.
■
Precautions in setting the LL PHASE
1. Press the LL PHASE’s “<” and “>” buttons at once, and the
phase will be back to its factory setting.
2. When the “<” and “>” buttons have been pressed at once, push
the “>” button once more to put the data in memory.
⑦
AES selector switch
The switch turns on and off the AES function.
When an auto iris
lens is used, be sure to keep this switch at OFF position.
⑧
Backlight compensation selector switch
The switch turns on and off the backlight compensation function.
⑨
AGC selector switch
The switch turns on and off the AGC function.
⑩
Lens selector switch
The switch has two positions, for a video iris lens and a DC iris lens.
⑪
Sync system selector switch
Used to choose between the internal sync and the line lock. Set the
selector to INT for use in internal sync, and LL for use in line lock. The
line lock cannot be used in regions with the power frequency of 50Hz.
⑫
Power indicator (POWER)
The LED indicator stays on in green while the camera power is on.
⑬
Video output connector (VIDEO OUT)
The output connector is connected to the video input connector of a monitor,
switcher or the like. (Terminate the terminal with a 75-ohm impedance.)
⑭
AC24V/DC12V power input terminal
Keep the input power at AC24V (21.6-26.4 V) or DC12V (10.5-15.0 V).
※
This installation should be made by a qualified service person
and should conform to all local codes.
E-5.
Connection
Video output connector (VIDEO OUT)
• This is the output connector of video signal.
• The connector is used to connect the video camera to the video
input connector of a monitor, switcher or the like. (To be connected
with 75-ohm impedance)
• Use a coaxial cable for connection.
ICD-505
VCR
MONITOR
E-6.
Specifications
(1) Imaging device:
1/3 inch, interline transfer type CCD
(2) No. of effective
Approx. 380,000 pixels,
picture elements:
768(H) and 494(V) lines
Color filter: Color difference line
sequential system
(3) Sensing area:
4.8(H) x 3.6(V) mm
(4) Horizontal resolution:
480 lines
(5) Minimum illuminance:
1 lux/F1.4 (at subject reflectance of 89%)
(6) S/N ratio:
48 dB/rms or better
(at rated illuminance)
(7) TV system:
2: 1 interlace, as per NTSC system
(8) Sync system:
Internal sync: Crystal lock or Line lock
(phase adjustable)
(9) Vertical sync frequency:
Int: 59.94Hz
Line lock: 60Hz
(10) Horizontal sync frequency: Int: 15.734KHz
Line lock: 15.750KHz
(Varies with power frequency for line-
lock SC notsynchronized)
(11) Video output:
VBS 1.0Vp-p/75 ohms
(12) White balance:
TTL method, ATW
(13) Backlight compensation:
On/off, switchable
(BLC)
(14) AES:
On/off, switchable, AES range 1 : 1600
(15) AGC:
On/off, switchable
(16) Auto iris function:
Video iris/DC iris, switchable
(DC iris level adjustable)
(17) Flange focal distance
adjustment function:
Provided
(18) Lens mount:
CS mount
(19) Camera mount:
1/4"-20UNC (top and bottom mounting)
(20) Ambient operating
temperature:
-10 to +50
°
C
(21) Power supply:
AC24V
±
10%, 60Hz /
DC12V (10.5-15.0 V)
(22) Power consumption:
Approx. 3.6W
(23) Input/output connectors:
(1) Video output; BNC
(2) AC24V/DC12V input;
2-pin terminal block
(3) Lens; 4-pin (applicable plug, E4-
191J-150 or equivalent option)
(24) Outer dimensions:
64(W) x 64(H) x 53(D) mm
(projections and accessories not included)
(25) Weight:
Approx. 250g (8.8 oz)
(26) Accessories:
Operation manual, 1 copy
(27) Option:
Lens connector plug E4-191J 150 or
equivalent 1pc.
E-7.
Warranty and after-sale
service
A warranty accompanies this product. Read and fill out the warranty card
that you have received at your dealer. Keep this card in a safe place.
· Please consult Ikegami Electronics (U.S.A.) Inc. or your dealer for full
warranty information. Your dealer will repair or replace free of charge
within the warranty period according to the warranty coverage.
· For repairs after the expiration of the warranty period, consult your
dealer or sales representative. It will first be judged whether the
trouble is repairable or not. Charged servicing will then be made
upon request of the user.
· Before you ask for servicing, take trouble of reading the Instruction Manual.
If the unit still fails, take note of the model number, date of purchase,
problem, etc. in detail, and inform your dealer or sales representative.
· If you have questions about the after-sale service, contact your
dealer or sales representative.
※
We suggest you ask for preventive inspection earlier.
①
Lens mount (CS mount)
This is used to mount the lens on the camera. Many types of CS
mount lens can be attached.
②
Focus lock screw (2 locations)
Used to mechanically fix the CS mount after adjusting the camera’s
flange focal distance. To adjust the distance, turn the CS mount and
move it to and from until a desired distance is obtained. The two lock
screws are positioned 90
°
to each other on top.
Auto iris lens
3
2
1
4
Auto iris lens
3
2
1
4
3
2
1
4
Numbers of connector pins
(Typical connections)
