IKEA PROFFSIG, Инструкция по эксплуатации

Страница: 12 / 164

12 ENGLISH
Adding special salt
If the special salt refill indicator lights up, add special salt to
the dispenser for special salt just before the programme
starts.
ATTENTION!
●
Detergent may damage the water softening system.
●
Only fill the dispenser of the water softening system
with special dishwasher salt.
●
Special salt can damage the tub due to corrosion.
●
To make sure that any special salt that escapes is
washed out of the tub, add the special salt to the dis-
penser for special salt immediately before the pro-
gramme starts.
→
Fig.
8
-
13
Adding rinse aid
If the rinse aid refill indicator lights up, top up with rinse aid.
Only use rinse aid for domestic dishwashers.
→
Fig.
14
-
17
Setting water softening system
Set the water hardness on your appliance.
→
Fig.
18
Overview of water hardness settings
You can find an overview of the water hardness values that can be selected here.
WATER HARDNESS °E HARDNESS RANGE MMOL/L SETTING VALUE
0 - 8 Soft 0 - 1.1 H:00
9 - 10 Soft 1.2 - 1.4 H:01
11 - 12 Medium 1.5 - 1.8 H:02
13 - 15 Medium 1.9 - 2.1 H:03
16 - 20 Medium 2.2 - 2.9 H:04
21 - 26 Hard 3.0 - 3.7 H:05
27 - 38 Hard 3.8 - 5.4 H:06
39 - 62 Hard 5.5 - 8.9 H:07
Regeneration of the water softening system – overview
In order to ensure fault-free function of the water softening system, the water softening system is regenerated in all pro-
grammes before the end of the main rinse cycle.
Here you can find an overview of the maximum additional running time and consumption values during regeneration of the
water softening system. You can find the column applicable to your product variant according to its water consumption in
the Eco 50° programme.
WATER CONSUMPTION IN
LITRES (DEPENDING ON
MODEL)
REGENERATION OF THE WATER
SOFTENING SYSTEM AFTER X
RINSE CYCLES
ADDITIONAL RUNNING TIME
IN MINUTES
ADDITIONAL WATER CON-
SUMPTION IN LITRES
ADDITIONAL POWER CON-
SUMPTION IN KWH
6.5 / 6.7 8 7 5 0.05
7.5 / 7.7 7 7 5 0.05
9.5 6 7 5 0.05
above 10.5 5 7 5 0.05
The consumption values specified are laboratory measure-
ments determined in accordance with the currently applic-
able standard and using the Eco 50° programme and the
factory value of the water hardness is set to 16 - 20°E.
Setting the amount of rinse aid
If there are streaks or water marks on tableware, change the
amount of rinse aid.
Note: A low level adds less rinse aid during the wash cycle, a
higher setting adds more rinse aid during the wash cycle.
→
Fig.
19
Detergent
Only use detergents that are suitable for dishwashers. Both
separate and combined detergents are suitable.
For optimum washing and drying results, use separate de-
tergent, adding special salt and rinse aid separately.
Note: Follow the manufacturer's instructions for each deter-
gent.
If you are using tablets, one is enough. Insert the tablets in a
horizontal position.
If you are using powder or liquid detergent, follow the man-
ufacturer's instructions and quantities for dosage in the de-
tergent dispenser.
20 ml – 25 ml detergent is sufficient for normal soiling. If
tableware is only lightly soiled, slightly less than the amount
of detergent specified is usually sufficient.
To download the full document, visit www.ikea.com