background image

ENGLISH

FCC DECLARATION OF CONFORMITY

Model Number:

MA203DT D

Trade Name:

iiyama

Responsible party:

IIYAMA North America, Inc.

Address:

65 West Street Road, Suite 101B, Warminster, PA 18974 U.S.A.

Telephone number:

215-682-9050

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This equipment may not cause harmful interference, and (2) this equipment must accept any interference
received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential environment. This equipment generates, uses and
can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If you determine the equipment does cause harmful interference to radio or
television reception (this may be determined by monitoring the interference while turning the equipment off
and on), you are encouraged to try to correct the interference by one of the following measures:

n

Reorient or relocate the receiving antenna.

n

Increase the separation between the equipment and receiver.

n

Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

n

Consult the dealer or an experienced radio or TV technician for help.

To meet the FCC requirements, the specified signal cables below should be used.

Signal Cable MB38 (Enclosed): 242Z050-01
Signal Cable MB31 (Optional): 242Z017-01

CE MARKING DECLARATION OF CONFORMITY

This Color Data Monitor complies with the requirements of the EC Directive 89/336/EEC “EMC Directive”,
73/23/EEC “Low Voltage Directive” as amended by Directive 93/68/EEC and 93/42/EEC “Medical Devices
Directive”.
The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential
areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the
buildings. All places of operation are characterized by their connection to the public low voltage power supply
system.

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus
as set out in the radio interference regulation of the Canadian department of communications.

CANADIAN DEPARTMENT OF COMMUNICATIONS  COMPLIANCE
STATEMENT

n

We reserve the right to change specifications without notice.

n

All trademarks used in this user manual are the property of their respective owners.

n

As an E

NERGY

  S

TAR

® 

Partner, iiyama has determined that this product meets the E

NERGY

  S

TAR

® 

guidelines for

energy efficiency.

CAUTION

Changes or modifications not expressly approved by iiyama could void the users authority
to operate the equipment under FCC compliance regulations.

Содержание MA203DT D






















Отзывы: