IHP Superior DRT4036TEN Скачать руководство пользователя страница 12

Страница: 12 / 40

Superiorfireplaces.US.com

126721-01_D

VENTING INSTALLATION

NOTICE: Read these instructions completely before

attempting installation.

These models are tested and approved for use with an IHP (direct

vent) pipe components and terminations.
The venting system must terminate on the outside of the structure and

can not be attached to a chimney or flue system serving a separate

solid fuel or gas burning appliance. A direct vent appliance must

have its own venting system. DO NOT common vent this appliance.
These models are approved to be vented either horizontally through

an outside wall or vertically through a roof or chase enclosure using

the following guidelines:
• When venting system terminates horizontally on an outside wall,

you may install a standoff if the termination cap is to be installed

directly on a combustible finish such as vinyl, wood, stucco, etc.

• Never run the vent downward as this may cause excessive tem-

peratures which could cause a fire.

• Vent pipe air space clearances to combustibles are 1" on all sides

except on the horizontal sections, which requires 2" clearance

from the top of the pipe. Where the termination cap penetrates a

combustible wall, 1" air space clearance is required.

• Have fireplace and selected vent components on hand to help

determine the exact measurements when elbowing or offsetting.

Always use wall firestops when penetrating walls and firestops

when penetrating ceilings or attic spaces.

• For installation of fireplace at elevations of 4000 feet or greater,

pay special attention to venting requirement recommendations.

WARNING: Read all instructions completely and

thoroughly before attempting installation. Failure to

do so could result in serious injury, property damage

or loss of life.

NOTICE: Failure to follow these instructions will void the

warranty.

NOTICE: Do not seal termination cap to vent pipe. Cap

must be removable for vent inspection and mainte-

nance.

INSTALLATION PRECAUTIONS

•  Wear gloves and safety glasses for protection
•  Use extreme caution when using ladders or when on roof tops
•  Be aware of electrical wiring locations in walls and ceilings
The following actions will void the warranty on your venting system:
•  Installation of any damaged venting component
•  Unauthorized modification of the venting system (Do not cut or alter

vent components)

• Installation of any component part not manufactured or approved

by IHP

• Installation other than as instructed by these instructions

WARNING: This gas fireplace and vent assembly

must be vented directly to the outside. The venting

system must NEVER be attached to a chimney serving

a separate solid fuel burning appliance. Each direct

vent gas appliance must use a separate vent system.

Do not use common vent systems.

WARNING: Vent pipe air space clearances to com-

bustibles are 1" on all sides except on the horizontal

sections, which require 2" clearances from the top

of the pipe. Where the termination cap penetrates a

combustible wall, 1" air space clearance is required.

INSTALLATION PLANNING

There are two basic types of direct vent installation:
• Horizontal Termination
• Vertical Termination
Horizontal Termination Installation

IMPORTANT:

Horizontal square terminations require only inner por-

tion of wall firestop. Horizontal installations using round termination

require exterior portion of wall firestop.

1. Set fireplace in its desired location and determine the route your

horizontal venting will take. Do not secure fireplace until all vent-

ing has been installed. Some installations require sliding fireplace

in and out of position to make final venting connections. Figures

15 and 16 on pages 12 and 13, show different configurations for

venting with horizontal termination that will help you decide which

application best suits your installation. Check to see if wall studs

or roof rafters are in the path of your desired venting route. If they

are, you may want to adjust location of fireplace.

2. Direct vent pipe sections and components are designed with

special twist-lock connections.

Twist-Lock Procedure:

Female ends of pipes have locking lugs

(indentations). These lugs will slide straight into matching slots

on male ends of adjacent pipes. Push pipe sections together and

twist one section clockwise approximately one-quarter turn until

sections are fully locked (see Figure 9, page 13).

Note: Horizontal runs of vent must be supported every three feet.

Use wall straps for this purpose.

3. Assemble desired combination of pipe and elbows to fireplace flue

collar. If there are long portions of venting run, pre-assembled

pipe sections may be installed as subassemblies for convenience.

4. Carefully determine location where vent pipe assembly will pen-

etrate outside wall. Center of hole should line up with center line

of horizontal vent pipe. Mark wall for an 11

" x 11

" square

hole. Cut and frame square hole in exterior wall where vent will

be terminated. If wall being penetrated is constructed of noncom-

bustible material, such as masonry block or concrete, an 8

hole with zero clearance is acceptable (see Figure 10, page 13).

WARNING: Do not recess vent termination into any

wall. This will cause a fire hazard.

Содержание Superior DRT4036TEN









































Результаты поиска

Содержание Superior DRT4036TEN

Отзывы:

Похожие инструкции для Superior DRT4036TEN

Бренды по названию

Популярные бренды

IHP Superior DRT4036TEN, Руководство пользователя

Результаты поиска

Содержание Superior DRT4036TEN

Отзывы:

Похожие инструкции для Superior DRT4036TEN

Бренды по названию

Популярные бренды