background image

INNOVATIVE HEARTH PRODUCTS  •  RHAPSODY

 LINEAR GAS FIREPLACES WITH SIT PROFLAME  •  GAS CONVERSION KIT INSTALLATION INSTRUCTIONS

2

NOTE: DIAGRAMS AND ILLUSTRATIONS ARE NOT DRAWN TO SCALE.

 

WARNING / AVERTISSEMENT

BURN HAZARD. Install only when fireplace is OFF and COLD.
Risque de brûlure. Installer seulement lorsque le foyer est éteint et froid.

 CAUTION / ATTENTION

Before proceeding with this conversion, the gas supply must be shut off prior to 

disconnecting the electrical power.

Avant de procéder à cette conversion, l’approvisionnement en gaz doit être 

coupée avant de débrancher l’alimenta tion électrique.

NOTICE

•  Read all steps before starting installation. 

•  These instructions must be left with the appliance.

•  All warnings, precautions, and instructions in the 

Installation Instructions

 

and 

Care and Operation Instructions

 provided with the appliance also apply to 

these instructions.

•  If you encounter any problems, need clarification of these instructions, or are 

not qualified to properly install this kit, contact your local distributor or dealer.

INSTALLATION INSTRUCTIONS
1. 

Shut OFF the gas supply to the appliance.

2. 

Disconnect the power supply at the circuit breaker.

3. 

Remove the bezel (if installed) by gently pulling out the lower edge of the bezel to 

detach it from the lower edge of the glass door frame. Then, swing the lower edge 

of the bezel away from the door, and lift up to unhook the bezel upper flange from 

the top edge of the glass door frame (see Figure 1).

[CROSS-SECTION]

Bezel Upper 

Flange

Glass Door

Frame

Bezel  

Lower 

Flange

Figure 1: Removing Optional Bezel

4. 

Remove the optional surround (if installed) by removing the nine (9) screws 

securing it (see Figure 2).

Figure 2: Removing Optional Surround

5. 

Remove the three (3) screws 

securing the lower edge of the glass 

door assembly to the fireplace. 

6. 

Grasp the glass door assembly by 

the sides, swing out the lower edge, 

and then lift up to unhook it from the 

fireplace. Take care not to damage 

the glass. Set aside the screws and 

door assembly in a secure location 

for later reinstallation (see Figure 3).

Glass Door Assembly

Figure 3: Removing Glass 

Door Assembly

7. 

Remove the media (if installed), 

following the instructions provided 

with the Media Kit.

8. 

Remove the two (2) 5/16 in. screws 

securing the burner to the burner 

brackets   (see Figure 4).

9. 

Carefully slide the burner to the left, 

to clear the venturi from the orifice. 

Then, rotate the burner to release 

the air shutter adjustment rod from 

the air shutter lever (see Figure 5). 

Set aside the screws and burner 

assembly in a secure location for 

later reinstallation.

10. 

Remove the control compartment 

access door and gasket by removing 

the twelve (12) screws securing 

them. Set aside the screws for later 

reinstallation (see Figure 4).

f i r e - p a r t s . c o m

Содержание RHAPSODY RHAP42N







Отзывы: