IHP GA9050A-1 Скачать руководство пользователя страница 3

IHP.US.com

126905-01_B

3

CHECK GAS TYPE

You must install this ON/OFF Safety Valve/Pilot Kit if your gas type 

is propane/LP. For additional convenience and safety, this ON/OFF 

Safety Valve/Pilot Kit can be used with natural gas. If you are unsure 

of the proper application, call dealer where you bought log set.
If the fireplace does not have a gas supply shutoff valve, one must 

be installed.

CONNECTING TO GAS SUPPLY

 WARNING: This appliance requires a 1/2" NPT 

(National Pipe Thread) inlet connection to the pres-

sure regulator.

 WARNING: A qualified service person must connect 

log set to gas supply. Follow all local codes.

 CAUTION: Never connect propane/LP appliance di-

rectly to the propane/LP supply. This appliance requires 

an external regulator (not supplied). Install the external 

regulator between the heater and propane/LP supply.

Installation Items Needed

Before installing log set, make sure you have the items listed below.
•  piping (check local codes)
•  sealant (resistant to propane/LP gas)
•  equipment shutoff valve*
•  test gauge connection*
•  adjustable (crescent) wrench or pliers
•  sediment trap
•  tee joint
•  pipe wrench
•  flexible gas line
•  10 mm Deep Socket
*An equipment shutoff valve with 1/8" NPT tap is an acceptable al-

ternative to test gauge connection. Purchase the optional equipment 

shutoff valve from your dealer.
For propane/LP units, the installer must supply an external regulator. 

The external regulator will reduce incoming gas pressure. You must 

reduce incoming gas pressure to between 11" and 14" of water. If 

you do not reduce incoming gas pressure, heater regulator damage 

could occur. Install external regulator with the vent pointing down as 

shown in Figure 2. Pointing the vent down protects it from freezing 

rain or sleet.

 WARNING: Never connect natural gas appliance 

to private (non-utility) gas wells. This gas is com-

monly known as wellhead gas.

 CAUTION: Use only new, black iron or steel pipe. 

Internally-tinned copper tubing may be used in certain 

areas. Check your local codes. Use pipe of 1/2" diam-

eter or greater to allow proper gas volume to log set. 

If pipe is too small, undue loss of volume will occur.

Installation must include an equipment shutoff valve, union, and 

plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook 

up. NPT tap must be upstream from log set (see Figure 3, page 4).

IMPORTANT: 

Install equipment shutoff valve in an accessible loca-

tion. The equipment shutoff valve is for turning on or shutting off 

the gas to the appliance.
Check your building codes for any special requirements for locating 

equipment shutoff valve to appliance.
Apply pipe joint sealant lightly to male NPT threads. This will prevent 

excess sealant from going into pipe. Excess sealant in pipe could 

result in a clogged burner orifice.

Figure 2 - External Regulator on Propane/LP Supply Tank with 

Vent Pointing Down 

External Regulator 

Vent Pointing Down 

Propane/LP Supply 
Tank 

INSTALLATION

 WARNING: Use pipe joint sealant that is resistant 

to liquid petroleum (LP) gas. 

We recommend that you install a sediment trap in supply line as shown 

in Figure 3. Locate sediment trap where it is within reach for cleaning. 

Install in piping system between fuel supply and heater. Locate sediment 

trap where trapped matter is not likely to freeze. A sediment trap traps 

moisture and contaminants. This keeps them from going into log set 

controls. If sediment trap is not installed or is installed wrong, log set 

may not run properly.

f i r e - p a r t s . c o m

Содержание GA9050A-1









Отзывы: