IHP astria Sirius42TEN Скачать руководство пользователя страница 41

Страница: 41 / 70

Installation

900079-00, 06/2017

Innovative Hearth Products
Sirius™ Linear Direct-Vent Gas Fireplaces

17.

Install the Finishing Materials

NOTE: See Cold Climate Insulation on

Page 11

and Vent Termination Clearances on

Page 13

1. Complete finished interior wall. Maintain a minimum 1” (26 mm) clearance from the door frame outer edge to

any finish material.

NOTE: NEVER install combustible material (wall finish, surround, trim, etc.) on, in front of, or overlapping any

part of the fireplace front face.

Figure 36 - Nailing flange attachment

Side

framing

Unit nailing flange

(no clearance to combustible

framing is required)

NOTE: See

Page 18

for finishing materials

thinner than 1”.

Finishing without optional Surround—Cleanface Finish

1. Secure nailing flanges to wall framing.

NOTE: The fireplace ships from factory with the flanges positioned for a cleanface installation.

NOTE: Install a second, field-supplied noncombustible board over the supplied noncombustible board. The

fireboard supplied with the unit is not intended to be the finish material.

2. Install non-combustible fiberboard at top of fireplace.

NOTE: If skimming the non-combustible fiberboard to match drywall, use Sheetrock

brand Durabond

setting type joint compound to fill all joints. These trademarks are owned by United States Gypsum Company or

a related company. A total of 1” non-combustible material is recommended.

3.  Finish out wall with 1/2” finishing materials – paint with high-temperature paint, etc.
4.  Install floor and media.
5.  Reinstall door and barrier.

Figure 37 - Noncombustible Material with Cleanface Finish

(1 ea.) Top non-combustible fireboard is

required

(provided). Secure it to the nailing

flange.

(2 ea.) Side non-combustible fireboard is

optional

(provided). Secure it to the nailing

flange. Do NOT install the side fireboards

if an optional surround is to be installed.

NOTE: The provided non-combustible fiberboard may be skim coated as a finish material, however, other types of

non-combustible board may provide a more durable surface.

Содержание astria Sirius42TEN







































































Результаты поиска

Содержание astria Sirius42TEN

Отзывы:

Похожие инструкции для astria Sirius42TEN

Бренды по названию

Популярные бренды

IHP astria Sirius42TEN, Инструкция по установке и эксплуатации

Результаты поиска

Содержание astria Sirius42TEN

Отзывы:

Похожие инструкции для astria Sirius42TEN

Бренды по названию

Популярные бренды