IHP astria Sirius42TEN Скачать руководство пользователя страница 1

Страница: 1 / 70

/06

/20

- Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a neigh-

bor’s phone. Follow the gas supplier’s instruc-

tions.

• If you cannot reach your gas supplier, call the

fire department.

- Installation and service must be performed by

a qualified installer, service agency or the gas

supplier.

WARNING:
FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could

result in serious injury, death, or property damage.

AVERTISSEMENT:
RISQUED’INDENDIE OU D’EXPLOSION

Le non-respect Des avertissements de sécurité

pourrait d’entraîner des blessures graves, la mort

ou des dommages matériels.

- Ne pas entreposer ni utilizer d’essence ni d’autres

vapeurs ou liquides inflammables dans le voisinage

de cet appareil ou de tout autre appareil.

- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

• Ne pas tenter d’allumer d’appareil.

• Ne touchez à aucan interrupteur. Ne pas vous servir

des téléphones se trouvant dans le bâtiment où

vous trouvez.

• Sortez immédiatement de bâtiment.

• Appelez immédiatement votre fournisseur de

gaz depuis un voisin. Suivez les instructions du

fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le service des incindies.

- L’installation et l’entretien doivent être assurés par

un installateur ou un service d’entretien qualifié

ou par le fournisseur de gaz.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future

reference.

Installateur : Laissez cette notice avec l’appareil.

Consommateur : Conservez cette notice pour

consultation ultérieure.

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only)

or mobile home, where not prohibited by local codes. This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit

is used.
Cet appareil peut installé dans une maison préfabriquée (mobile) déjà installée à demeure, si les réglements

locaux le permettent. Ce appareil doit être utilisé uniquement avec le type de gaz indiqué sure la plaque

signalétique. Cet appareil ne peut être converti à d’autres gaz, sauf si une trousse de conversion est utilsée.

Installation and Operation Instructions

Models

PFS

Report No. F14-108

Ce manuel est disponible en francais, simplement

en faire la demande. Numéro de la pièce 900079-01.

P/N 900079-00 REV. E 06/2017

Sirius™ Direct-Vent Gas Fireplaces

Sirius42TEN

Sirius42TEP

Sirius54TEN

Sirius54TEP

P900079-00

Содержание astria Sirius42TEN







































































Результаты поиска

Содержание astria Sirius42TEN

Отзывы:

Похожие инструкции для astria Sirius42TEN

Бренды по названию

Популярные бренды

IHP astria Sirius42TEN, Инструкция по установке и эксплуатации

Результаты поиска

Содержание astria Sirius42TEN

Отзывы:

Похожие инструкции для astria Sirius42TEN

Бренды по названию

Популярные бренды