•
To use device as an Adapter with external audio source do not insert USB
(or SD card)
then connect the included AC adapter
•
To use internal audio, Insert the USB flash drive
(or SD card)
1
st
then connect the included AC adapter
(110- 240 V AC to 5V DC) do not
use a different power adapter or the unit will be damaged – it may take up to 60 seconds before playback starts with USB flash drive blinking
•
Confirm that white LED lights in front of unit are double blinking –
for regular phones continue,
for PBX phones go to page P4
•
Use one of your telephones and unplug the cord for L1/L2 from it and connect it to L1/L2 IN jack on iHold device , now
connect the L1/L2 OUT jack to your telephone using the provided cord, check for dial tone on lines 1 & 2
•
If applicable unplug the cord for L3/L4 from telephone and connect it to L3/L4 IN jack on iHold device, now connect the
L3/L4 OUT jack to your telephone using the provided cord, check for dial tone on lines 3 & 4
•
Wait till LED lights turn OFF - observe that after you connect the lines the blinking lights 1
st
stops then turns OFF after 20
seconds
(on non existing lines the lights keep blinking and that is OK)
•
Turn the speaker ON to confirm audio is playing and adjust the volume to mid level
(you can Turn it OFF any time)
Switch set to 1: Hold button activation
C
Use this setting when all phones are corded ( not cordless type like corded base s portables) and all are same model
and are compatible for hold button activation (for example all are ATT 993, At&t ML 17929)
Operation: make or receive a real call, the LED on the iHold turns ON solid, then simply press the button on your
telephone, the Music will be heard to the caller and the LED on the iHold device starts to BLINK
,
to return to the call just re-
select that line. (Be sure to allow 1 or 2 seconds before putting a call on HOLD).
The 1
st
time your are setting the device If it did not work hang up and try it again 2 or 3 times.
If music on hold does not work in this setting
(for example ATT 1040,1070,1080)
, hang up and change switch to setting 2 or 3
Switch set to 2: Flash activation
C
This setting utilizes
Flash then Hold
activation method, this setting supports any phone or any mix of brands with instant
activation by pressing Flash then Hold
Operation: make or receive a real call, the LED on the iHold turns ON solid, then simply press the then
button on your telephone, the Music will be heard to the caller and the LED on the iHold device starts to BLINK
,
to
return to the call just re-select that line and speak into the audio to stop it for example say :
“Hi I am Back”
Alternatively you may just press
to stop the audio (Be sure the call has been on Hold at least
5 seconds
before you try
to voice deactivate or Flash to stop the audio)
If for some reason you are not able to voice -deactivate, try speaking louder or more direct into the microphone or use the Flash
button to deactivate audio.
L1/L2
OUT
110 - 240 V
HOLD
FLASH
HOLD
L1 L2
Please note: just
one telephone
may be connected
to this device,
other telephones
remain connected
to their own wall
jacks and they all
work.
L1/L2
IN
1 2 3
A B C
Front
Back
L3/L4
IN
L3/L4
OUT
NXT L3 L4
Volume
Not used
FLASH
1 2 3
The FLASH button could be labeled as
Call Wait
or
LINK
or
ON
or
TALK
button on some telephones
USB drive
SD card slot
Not used
Speaker
ON OFF OFF
P1
In setting 2 do not make the volume too loud or the audio could sound flickering when heard on Hold
Audio output
to PBX or
external
audio Input
1 2 3
LED
i
Hold 4LP-S
Advanced Music On Hold Adapter / All-In-One device
(If using External audio connect it to RCA jack as shown and use your external audio volume control)
