Ignite Blade Box 48 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 32

Ignite Blade Box 48 Скачать руководство пользователя страница 15

13

Figure 11

c138245a

10. Lower the top link (Item 1) [Figure 11] until it aligns

with the implement upper mounting hole.

11. Install the pin (Item 2) and retainer pin (Item 3)

NOTE:

It may be necessary to lengthen or shorten

the top link to align it with the implement
mounting hold [Figure 11].
(See Adjusting The Top Link on Page 13)

12. The implement can be leveled front to back by

adjusting the top link.
(See Adjusting The Top Link on Page 13)

13. The implement side to side sway will need to be

adjusted. (See Adjusting The Sway Bar on Page 14)

Adjusting The Lift Link

Figure 12

p138247b

The lift link (Item 1) [Figure 12] is used to adjust the side
to side level of the implement.

See the compact tractor Operation & Maintenance
Manual for detailed information on adjusting the lift link.

Adjusting The Top Link

Figure 13

c138246a

The top link (Item 1) [Figure 13] is used to adjust the front
to back level of the implement.

1.

Loosen the locknut (Item 2) and use the adjuster
(Item 3) [Figure 13] to lengthen or shorten the top
link.

2.

Turn clockwise to lengthen the top link, turn
counterclockwise to shorten top link.

3.

After the implement has been leveled, tighten the
locknut (Item 2) [Figure 13].

OPERATING INSTRUCTIONS

«
...
13
14
15
16
17
...
»

Содержание Blade Box 48

































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды