background image

 

REFRIGERATION LTD 

 

www.igloorefrigeration.com

 | 

Ice Cream/ Gelato

 

 

Figure 4 Leveling legs  

A – Screw the feet in the nuts welded to 
the frame of the unit 
 

3.2. Unit Location 

 

Remove cardboard angles and protective foil. 

 

Install the unit on a strong and level surface. 

 

To ensure proper operation the unit must be leveled from front to back and left to right. 

 

Unit may malfunction if improperly leveled. 

 

Be sure there is sufficient ventilation around the entire unit 

 

Select a location a way from heat and moisture generating equipment. 

 

Avoid installation in a high ambient or humid location. 

 

High ambient temperatures will cause the compressor to overwork. 

 

Humidity may cause rust, condensation around glass or stainless steel and decrease the efficiency of the 
unit. 

3.3. Connection and start-up 

 

Unpack the unit. 

 

Place the unit on an even and hard base. Then level the unit with the levelling legs. 

 

 

 

 

Remove the protection foil from the elements of the unit (e.g. from the inside of the unit, display shelves, 
front bumper). 

 

To securely transport the equipment, the unit may be shipped partially disassembled. If the user received 
the unit partially disassembled, perform the following operations: 
1.

 

Place cross-bars under stainless steel containers (Figure 5/4) 

2.

 

Place containers according to Figure 2 or Figure 3 

3.

 

Slide in glass sides according to Figure 5/2 

 

The equipment should be cleaned right after unpacking and before turning it on. The unit should be cleaned 
with warm water not exceeding 40°C with a neutral detergent. For washing and cleaning the equipment, it 
is prohibited to use products containing chlorine and sodium varieties, which destroy the protective layer 
and components of the equipment! Any residue of adhesives or silicone on metal elements should be 
removed only with extraction naphtha (not applicable to items made of plastic). Do not use other organic 
solvents. 

When cleaning the unit, do not use water jet.  The unit should be cleaned with a 
moist cloth. 

 

 NEMA Plugs         

IGLOO refrigeration uses this type of plug. If you 
do not have the right outlet, have a certified 
electrician install the correct power source. 

115/60/1 
NEMA-5-20R 
 

Содержание ARBF Series















Отзывы: