background image

5.3.2 Procedure 

 

Connect according to wiring diagram (5.3.1). 

 

Pierce or pull out cable feedthrough and feed connection cable through. 

 

Check supply voltage. See name plate for permissible voltage. 

 

Use  a  shielded  connection  cable  for  the  probe:  e.g.  LIYCY  min.  0.75  mm²  up  to  a  max. 
length of 50 m.  LIYCY min. 1.5 m² up to a max. length of 100 m (see note). 

 

Use a shielded cable for the current output (see note).  

 

Only connect shielding on the FLB1 control unit (terminal 12). 

 

After connecting to the power supply – with the device disconnected – place the hood on 
the base and tighten the fastening screws. 

 

Fit  electrode  according  to  separate  assembly  instructions  and  connect  as  in  the  wiring 
diagram. 

 

When  installing  it,  check  whether  the  cables  used  are  UV-resistant  and  that  UV 
protection is ensured on the installation side if necessary. 
The cable must not come into contact with heat-conducting parts. 

 
For aligning the probe plug to the local circumstances, the upper nut can be released (

 33.5mm). 

In doing so, take care not to move the plug in the probe!! (SW24). 
The contact carrier can be carefully turned into the correct position. 
On refitting ensure that the seal is correctly seated! Retighten the upper nut without moving the 
plug in the probe. 
 
 

The connector plugs must be wired according to the wiring diagram. 

 

 

Caution

 

Содержание FLB1



















Отзывы: