iGage iG5 Скачать руководство пользователя страница 43

Страница: 43 / 96

iG5 User Manual

remember that a 2-hour OPUS static observation has an
expected height accuracy of 2.5 cm. A 6-hour occupation has
an expected accuracy of 1.5 cm.

OPUS-RS (Rapid Static)

Standard OPUS-Static sessions require 2-hour observations.
OPUS-RS sessions can be as short as 15-minutes.

OPUS-RS solutions are not available universally. In general,
OPUS-RS requires:

3 (or more) CORS within 250 km of your site
your site must be within 50 km of the polygon formed by
the CORS sites

If you are working in Southwest Nevada, along the high line of
Montana or in North or South Dakota, OPUS-RS probably will
not work and you will have to collect at least 2-hours of data
for submission to OPUS-STATIC.

Prior to collecting data for OPUS-RS you can check the latest
status map to insure that OPUS-RS will work. The online
OPUS-RS resource:

Содержание iG5

































































































Результаты поиска

Содержание iG5

Отзывы:

Похожие инструкции для iG5

Бренды по названию

Популярные бренды

iGage iG5, Руководство пользователя

Результаты поиска

Содержание iG5

Отзывы:

Похожие инструкции для iG5

Бренды по названию

Популярные бренды