ifrogz AIRTIME PREMIER, Быстрый старт

Страница: 4 / 8

AIRTIME
™
PREMIER Instructions
Introduction
Welcome to truly wireless audio. Now, you never
need to plug your earbuds in again. AIRTIME
PREMIER truly wireless earbuds free you to enjoy
music without anything holding you back.
Pairing the Wireless Earbuds with
Your Device
1. Simply open the case and remove the buds.
A pairing signal will be sent to your Bluetooth®
device. The earbuds will flash white and red,
indicating pairing mode.
2. Ensure your device’s Bluetooth® connection is
on and select “IFROGZ Airtime Premier.”
3. Complete any additional pairing steps based
on your device. The earbuds’ lights will flash
white and then turn off, indicating that pairing
was successful. Congrats, your new wireless
earbuds are now ready to use!
Turning Earbuds On/Off
To turn the earbuds on, simply remove the buds
from the case.
If you would like to use only one bud, simply remove
the right earbud from the case. The right earbud is
the primary bud and can be used without the other.
Please note, the left earbud will not work alone
unless the right earbud is also removed
from the case.
To turn earbuds off, simply return them to the case.
You can also press and hold the IFROGZ icon on the
earbud for ten seconds to turn it off; it will flash red
indicating power is off.
The earbuds will go into hibernation mode if not
used for 20 minutes.
Using the Earbuds
AIRTIME PREMIER has built-in touch navigational
controls. Simply tap on the end of the earbud (on the
IFROGZ logo) to navigate.
Music Controls
Left Bud Actions Right Bud
Play / Pause Quick Tap Play / Pause
Previous Track
2x Taps
Next Track
Decrease Volume
Tap & Hold
Increase Volume
Call Controls
Answer Call /
End Call
Quick Tap
Answer Call /
End Call
Cancel Call
Tap & Hold
Cancel Call
Siri / Voice
Command
3x Taps
Siri / Voice
Command
Charging the Wireless Earbuds
The case carries enough power to charge the
earbuds up to 5
*
times. To charge them:
1. Place them in the charge case.
2. A red light on the earbuds will indicate
charging. When the red light disappears,
they are fully charged.
3. Recharge the case, if needed.
*
Based on 50% volume and 5 hours of playtime.
Charging the Case
Your case comes charged and ready to go, but
here’s how to recharge it when you need to:
1. Connect the included USB-C charging cable to
the port on the back of your case.
2. Connect the USB-A end of the included cable
to your preferred 5V USB outlet.
3. The Battery Indicator outside the case will
flash according to its current battery level. This
indicates your case is charging.
4. Wait for the Battery Indicator lights to turn off,
indicating your case is fully charged.
5. Disconnect the charging cable and enjoy your
new, portable power.
Checking the Battery Level
Your case carries enough power for you to enjoy
your wireless earbuds up to 5 times, for a total of up
to 30 hours. To check how much power it still carries:
1. Place the buds in the case. The LED on the front
of the case will illuminate indicating how much
battery remains:
a. If it lights up completely, 75% or
more remains.
b. If it lights up ¾ of the way,
between 50-74% remains.
c. If it lights up ½ of the way,
between 25-49% remains.
d. If it lights up ¼ of the way, less
than 24% remains.
2. Recharge your case whenever you wish.
Factory Reset
A factory reset can help with some troubleshooting
issues. Here’s how to perform one:
1. Place both buds in the case.
2. Reset the right bud.
a. Remove the right bud from
the case.
b. Tap and hold for 10 seconds
until light flashes red and
turns off.
c. Tap and hold for five seconds
until light turns on and flashes
red and white.
d. Quickly tap the bud six times,
the light will turn off.
e. Return the bud to the case.
3. Reset the left bud.
a. Remove left bud from the case.
b. Quickly tap the bud six times,
the light will turn off.
c. Return the bud to the case.
4. Connect left and right.
a. Remove both buds from the
case and allow them to connect
to each other for about five
seconds.
5. Connect as normal.
a. The buds are now reset to
factory settings. Remove
them from the case and pair
as normal.