IFM TCC8 Series Скачать руководство пользователя

Страница: 18 / 21

9.1 Parameters

Parameter

Explanation

ou2

Configuration of the analogue signal: I = 4��20 mA or Ineg = 20��4 mA

or OFF = output off

P-n

Switching logic for the diagnostic output: PnP or nPn�

ASP2

Analogue start point for measured temperature value�

AEP2

Analogue end point for measured temperature value�

FOU2

Analogue signal in case of an alarm: On = 21�5 mA; OFF = 3�5 mA�

ccL

Calibration check limit = temperature deviation between the process

value and the reference value from which the unit provides a warning�

uni

Setting of the standard unit of measurement: °C or °F�

LED mode

The LED on the unit can be switched on and off:

On = LED always on

Off = LED always off

Notification = LED only on in case of a warning or an alarm�

Restore Factory

Settings

Restore the factory settings�

We recommend recording your own settings before carrying

out a reset

(→ 14 Factory setting)

�

9.2 Analysis functions

Displays /

commands

Explanation

Free-text fields for

device information

-Application Specific Tag

-Function Tag

-Location Tag

-Installation date

Diagnostics display

-Hi = highest temperature value measured

-Lo = lowest temperature value measured

Flash On / Flash Off

The LED starts flashing, allowing easy identification of the unit

in the field�

Reset

-[Hi] and [Lo] memory

-[Hi] memory

-[Lo] memory

Reset the maximum and/or minimum value memories

Содержание TCC8 Series






















Результаты поиска

Содержание TCC8 Series

Отзывы:

Похожие инструкции для TCC8 Series

Бренды по названию

Популярные бренды

IFM TCC8 Series, Руководство по эксплуатации

Результаты поиска

Содержание TCC8 Series

Отзывы:

Похожие инструкции для TCC8 Series

Бренды по названию

Популярные бренды