IFM PQ78 Series Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 19

IFM PQ78 Series Скачать руководство пользователя страница 13

13

UK

• Change from menu level 1 to menu level 2:

►

Press [Mode/Enter] until [EF] is

displayed�

If the submenu is protected with an

access code,"Cod1" flashes in the

display�

►

Press [Set] and keep it pressed until

the valid code no� is displayed�

►

Press [Mode/Enter] briefly�

On delivery by ifm electronic: no access

restriction�

►

Press [Set] briefly�

> The first parameter of the sub-menu

is displayed (here: [uni])�

• Locking / unlocking

The unit can be locked electronically to prevent unintentional settings�

►

Make sure that the unit is in the

normal operating mode�

►

Press [Mode/Enter] + [Set] for 10 s�

> [Loc] is displayed�

During operation: [Loc] is briefly displayed if you try to change parameter values�
For unlocking:

►

Press [Mode/Enter ] + [Set] for 10 s�

> [uLoc] is displayed�

On delivery: unlocked�

• Timeout:

If no button is pressed for 15 s during parameter setting, the unit returns to the

operating mode with unchanged values�

«
...
11
12
13
14
15
...
»

Содержание PQ78 Series




















Отзывы:

Нет отзывов